|
| Nigel |
|
||
|
Does anyone have the correct tool to remove the AU Balancer? - mine doesnt have any bolt holes for the nice cheap removers.
I saw the tool at Autobarn, but its almost $200. I only need it for about 5 minutes to pull the balancer so I can do the front oil seal Anyone? Nigel Last edited by Nigel on Sat Sep 27, 2008 12:06 pm, edited 1 time in total. |
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
Nigel wrote: Does anyone have the correct tool to remove the AU Balancer? - mine doesnt have any bolt holes for the nice cheap removers.
I saw the tool at Autobarn, but its almost $200. I only need it for about 5 minutes to pull the balancer so I can do the front oil seal Anyone? Nigel good luck |
||
| Top | |
||
| Nigel |
|
||
|
Thanks. I found a local "mobile mechanic" around the corner had the tool.
He removed the balancer, and replaced the seal for me for the cost of the callout. Too easy. |
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
Nigel wrote: Thanks. I found a local "mobile mechanic" around the corner had the tool.
He removed the balancer, and replaced the seal for me for the cost of the callout. Too easy. what was the callout fee? |
||
| Top | |
||
| Nigel |
|
||
|
$75. Him, His tool, and new seal installation.
The tool is $186 at Autobarn... Saw it, thought id never use it the three times it would take. |
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
i take it you already had every thing els removed?
$75 isn't to bad considering the cost of the tool |
||
| Top | |
||
| Nigel |
|
||
|
by "everything else" you mean the thermo fans?
That was all it took. Its s bloody wonder ford cost so much. |
||
| Top | |
||
| Xflow |
|
|||
Age: 36 Posts: 721 Joined: 31st Dec 2005 Ride: EF V8 Futura, 180sx Location: Brisbane, Burpengary |
this might sound dodgy but it worked like a charm
i undid the bolt and hit it with hammer a few time to crack the seal then use to pry bars one each side of the hamonic balancer and pushed and get some one to softly tap the harmonic balancer and it comes off. best to do the job from under the car and get someone to do the tapping from above.
_________________ Ford EF Futura Black
|
|||
| Top | |
|||
| gogetta |
|
|||
|
yeah i guess u should only "tap" it and not bash it...else the thrust bearing might get damaged
_________________ |
|||
| Top | |
|||
| relaxed_diplomacy |
|
||
|
The outer cast iron ring isn't very strong either. I wasn't doing anything serious yet managed to chip some metal off one when i was removing if from a wrecked motor, which of course ruins the balance if nothing else, game over.
_________________ wrecking 9/97 EL fairmont sedan burgundy 6cyl auto 270k modBAintake |
||
| Top | |
||
| FPV_GTp |
|
||
|
Nigel wrote: Does anyone have the correct tool to remove the AU Balancer? - mine doesnt have any bolt holes for the nice cheap removers.
I saw the tool at Autobarn, but its almost $200. I only need it for about 5 minutes to pull the balancer so I can do the front oil seal Anyone? Nigel Hi , yes very expensive yes indeed , make one ? here is a link to one I made , Homemade Harmonic balancer puller 4 AU 6 cyl http://www.fordmods.com/forums/viewtopi ... r%20puller
_________________ WANTED - Complete BTr4 and zf 6hp26 automatic transmission 6 cylinder and V8 transmission(s) suit rebuild? Drop me a PM if you can help would be greatly appreciated - thanks |
||
| Top | |
||
| speedie51 |
|
||
|
have series 2 au falcon with a broken harmonic ballancer, how do i stop the ballance from turning while i undo the nut as i have a auto and just turns engine over tried the alloy tooth ring on back of pully but only broke away teeth as its only alloy and week. please help any other way.
|
||
| Top | |
||
| Nigel |
|
||
|
Oh dear - breaking the teeth of isnt good. Thats your timing sensor triggers!. They come on a new balancer though dont they?
The easiest way is to have the fan belt on, and hold the fan belt still while you undo the bolt. If that doesnt work, a rattle gun, or, you can remove the started and jam the ring gear. Nigel |
||
| Top | |
||
| JackoTJK |
|
||
|
telstra rope down a spark plug works. And no I haven't bent a valve and have done it heaps
_________________ JackoTJK |
||
| Top | |
||
| EFFUTURA4.05SP |
|
|||
|
Nigel wrote: Does anyone have the correct tool to remove the AU Balancer? - mine doesnt have any bolt holes for the nice cheap removers. I saw the tool at Autobarn, but its almost $200. I only need it for about 5 minutes to pull the balancer so I can do the front oil seal Anyone? Nigel Are you kidding??? I have those tools for sale at work in Stanley for like $25 TOPS! WTF, maybe I should start selling them!
_________________ 1996 EF Futura factory manual |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 90 guests |
