|
theblackone |
|
|||
|
i just cleaned my ISC on my EF XR6 .. took it for a run.. still had troubles with the car nearly stalling .. anyway got near home and everytime i let off the accelerator.. it would just stall.. it seems like it did not want to idle
got home.. turned her over.. starts up.. then stalls. did i accidentally touch something that i shouldnt have? it is as if the car is not idling at all... i start the car, car turns on.. revs for a second.. drops down to 100rpm and stalls. :S any help will be greatly appreciated.
_________________ SIGNATURE REMOVED - REFER TO FORUM GUIDELINES! |
|||
Top | |
theblackone |
|
|||
|
on duel fuel too..
_________________ SIGNATURE REMOVED - REFER TO FORUM GUIDELINES! |
|||
Top | |
stockstandard |
|
|||
|
Id check all the plugs, look for missing vacuum hoses, and run diagnostics on the computer.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
Top | |
theblackone |
|
|||
|
plugs are ok.. leads are ok.. no vacuum hoses missing ... how do i adjust idle?
_________________ SIGNATURE REMOVED - REFER TO FORUM GUIDELINES! |
|||
Top | |
stockstandard |
|
|||
|
There is a stop screw on the side of the TB
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
Top | |
theblackone |
|
|||
|
ok i increased the idle screw.. that seems to work.. why did i have to do that?
_________________ SIGNATURE REMOVED - REFER TO FORUM GUIDELINES! |
|||
Top | |
stockstandard |
|
|||
|
theblackone wrote: ok i increased the idle screw.. that seems to work.. why did i have to do that?
Dont know. Maybe the ISC was stuck open and now that you have cleaned it it closes all the way so you need to open the butterfly more.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
Top | |
Soulfire |
|
|||
|
because your idle speed was set too low? :p
|
|||
Top | |
stuzzy |
|
|||
|
was ur problem just on gas or petrol aswell cause mine was doing this yesterday just on gas not petrol but today it backfired again so yeah thats after the mechanic said he fixed it
|
|||
Top | |
theblackone |
|
|||
|
it was doing it on both... what did ur mechanic say they did?
what i did was just cleaned the ISC and put it back.. and then took it for a spin but it kept stalling. i was pretty sure it had to do with the idle screw .. as i checked everything out (leads/plugs/hoses). but i dont understand why it would stall and not just run at low revs? ... strange s**t
_________________ SIGNATURE REMOVED - REFER TO FORUM GUIDELINES! |
|||
Top | |
86gav |
|
|||
|
you didnt do something silly like leave it disconnected did you?
_________________
|
|||
Top | |
theblackone |
|
|||
|
nup...everything was in .. as soon as i touched the idle screw it worked...
weird?
_________________ SIGNATURE REMOVED - REFER TO FORUM GUIDELINES! |
|||
Top | |
MacGyver |
|
|||
|
I'd check to make sure the ISC is still working. Sometimes when cleaning them, you can get some fluids inside that screws them up. If your ISC fails then you car will not idle, unless you up the idle speed (which you have done). I'd say the ISC is stuffed. When you get a new one make sure you follow the proper procedure to set base idle. I think it is deisconnect ISC plug and place a 0.75 (or is it a 1.1)mm feeler guage between the idle adjust screw and set idle to 600rpm.
cheers Scott
_________________ If it doesn't fit, jam it. If that doesn't work use a hammer. - Engineers Motto |
|||
Top | |
NC 5ltr |
|
|||
|
I had a similar prob to yours but was only stalling on gas,turned out the earthing wire was disconnected and was causing it to stall everytime i switched it to gas.
_________________ "Looking at cleavage is like looking at the sun. You don't stare at it. It's too risky. You get a sense of it and then you look away."
|
|||
Top | |
falcon4litreOHC |
|
|||
|
The problem you have will be your 02 sensor. I had a similar problem... Check your fault codes to seen if your 02 sensor is running lean.............
|
|||
Top | |
Who is online |
---|
Users browsing this forum: Google Adsense [Bot] and 71 guests |