Fordmods Logo

Hot 3.9 

 

Page 1 of 2 [ 24 posts ] Go to page 1, 2  Next

 
 Post subject: Hot 3.9
Posted: Mon Nov 14, 2005 2:30 pm 
Smokin em up
Offline
User avatar

Age: 40

Posts: 237

Joined: 7th Jan 2005

Gallery: 3 images

Ride: BA XR6 Falcon

Location: Hawthorn
VIC, Australia

THe other day I noticed my cars Temp gauge was mving up faster then my Tacho, so I though thats a bad sign right there.

But then on the open road it is fine, It runs normalish.

Then I filled the radiator up and there was no sign of leaks or anything.
I got to bendigo and I had no water in my radiator again.

I didnt overheat, but it did go beyond Hot. I didnt loose any power
and there were no signs of vapour pouring from under the hood.

Could it be that my radiator is gone or is it something much much worse

 

_________________

Jesus Drove Fords

Proud Owner of a XR6 MkII

Top
 Profile  
 
 
Posted: Mon Nov 14, 2005 3:11 pm 
Getting Side Ways
Offline
User avatar

Age: 37

Posts: 3186

Joined: 8th Nov 2004

Gallery: 6 images

Ride: EF Falcon

Location: Townsville
QLD, Australia

Could be any number of things, head gasket, hoses, radiator core.

I presonally hads a similar thing, but it wasnt loosing water as quickly or overheating, and the o rings in the side of the radiator were shagged!! Cost $270 to get the core celaned and new side tanks and o rings and stuff, as opposed to the $1400 i was told to do the head gasket!! :D

 

_________________

Nicco's M112 Blown, T-56 equipped EF
forums/viewtopic.php?t=68319

Top
 Profile  
 
 
Posted: Mon Nov 14, 2005 3:14 pm 
Smokin em up
Offline
User avatar

Age: 40

Posts: 237

Joined: 7th Jan 2005

Gallery: 3 images

Ride: BA XR6 Falcon

Location: Hawthorn
VIC, Australia

Wouldnt you notice the power loss if the head gasket was shot.

I am hoping for a radiator, all the hoses are nice and soft with no splits.

I think I am hoping for anything other then a Head.

How did you find out it was your O-rings, was it a good machanic who didnt s**t you, or just your own investigation?

 

_________________

Jesus Drove Fords

Proud Owner of a XR6 MkII

Top
 Profile  
 
 
Posted: Mon Nov 14, 2005 4:16 pm 
Getting Side Ways
Offline
User avatar

Age: 61

Posts: 4102

Joined: 18th Nov 2004

Gallery: 10 images

Ride: PX2 Ranger 4x4 XLT Dual CAB

Location: Carrum Downs
VIC, Australia

If theres no sign of any leaks and your loosing coolant, then its either going out the exhaust pipe (head problems) or its overpressurizing and blowing it out the radiator cap!

Check over the whole engine again for signs of coolant leaks, including under each manifold.
Strap a small coke bottle to the overflow pipe, then after a drive see if there is any coolant inside it.

 

_________________

Image
She's meanness put to music and the b**ch is born to run!
Like the sign says, "speed's just a question of money. How fast can you go?"

Top
 Profile  
 
 
Posted: Mon Nov 14, 2005 4:23 pm 
Smokin em up
Offline
User avatar

Age: 40

Posts: 237

Joined: 7th Jan 2005

Gallery: 3 images

Ride: BA XR6 Falcon

Location: Hawthorn
VIC, Australia

OK i will do the coke thing tonight. Just the word "Head problems" sends shivers down my spine.

 

_________________

Jesus Drove Fords

Proud Owner of a XR6 MkII

Top
 Profile  
 
 
Posted: Mon Nov 14, 2005 4:36 pm 
Tyre Shredder
Offline
User avatar

Age: 41

Posts: 374

Joined: 22nd Dec 2004

Ride: EB 5Spd

Location: Brisbane
QLD, Australia

also check your water pump bearing, mine started having the same symptoms as yours and turned out it was flowing out from there, couldnt see it very easily as it started leaking underneath, worth a shot

 

_________________

Image

Top
 Profile  
 
 
Posted: Mon Nov 14, 2005 4:57 pm 
Smokin em up
Offline
User avatar

Age: 40

Posts: 237

Joined: 7th Jan 2005

Gallery: 3 images

Ride: BA XR6 Falcon

Location: Hawthorn
VIC, Australia

I will thanks for that.

I think I will give anything a shot before I start pulling the engine right apart.

 

_________________

Jesus Drove Fords

Proud Owner of a XR6 MkII

Top
 Profile  
 
 
Posted: Mon Nov 14, 2005 5:51 pm 
Getting Side Ways
Offline
User avatar

Age: 37

Posts: 3186

Joined: 8th Nov 2004

Gallery: 6 images

Ride: EF Falcon

Location: Townsville
QLD, Australia

ebjamie wrote:
Wouldnt you notice the power loss if the head gasket was shot.

I am hoping for a radiator, all the hoses are nice and soft with no splits.

I think I am hoping for anything other then a Head.

How did you find out it was your O-rings, was it a good machanic who didnt s**t you, or just your own investigation?


Good mechanic.

He was doing a pressure test on it for me. and went to go do some other things and got held up (lol) and when he came back there was just a bit of water under the radiator.

He traced it back and found that this was where it came from.

 

_________________

Nicco's M112 Blown, T-56 equipped EF
forums/viewtopic.php?t=68319

Top
 Profile  
 
 
Posted: Tue Nov 15, 2005 9:01 am 
Smokin em up
Offline
User avatar

Age: 40

Posts: 237

Joined: 7th Jan 2005

Gallery: 3 images

Ride: BA XR6 Falcon

Location: Hawthorn
VIC, Australia

OK last night i tried the coke bottle thing and it only caught a very small amount of water, although saying that I only droe about 30 kms last night.

 

_________________

Jesus Drove Fords

Proud Owner of a XR6 MkII

Top
 Profile  
 
 
Posted: Tue Nov 15, 2005 12:57 pm 
Getting Side Ways
Offline
User avatar

Age: 61

Posts: 4102

Joined: 18th Nov 2004

Gallery: 10 images

Ride: PX2 Ranger 4x4 XLT Dual CAB

Location: Carrum Downs
VIC, Australia

ebjamie wrote:
OK last night i tried the coke bottle thing and it only caught a very small amount of water, although saying that I only droe about 30 kms last night.


Still it proves that some coolant is coming out of the cap, now you need to find out why. First start with a new cap.

 

_________________

Image
She's meanness put to music and the b**ch is born to run!
Like the sign says, "speed's just a question of money. How fast can you go?"

Top
 Profile  
 
 
Posted: Tue Nov 15, 2005 4:52 pm 
Smokin em up
Offline
User avatar

Age: 40

Posts: 237

Joined: 7th Jan 2005

Gallery: 3 images

Ride: BA XR6 Falcon

Location: Hawthorn
VIC, Australia

OK it is booked in tomorrow for a service and I have also made them aware that it is overheating and stuff.

Will keep you all informed.
Thanks for all the info though.........fingers crossed it aint the head.

 

_________________

Jesus Drove Fords

Proud Owner of a XR6 MkII

Top
 Profile  
 
 
Posted: Thu Nov 17, 2005 8:48 am 
Smokin em up
Offline
User avatar

Age: 40

Posts: 237

Joined: 7th Jan 2005

Gallery: 3 images

Ride: BA XR6 Falcon

Location: Hawthorn
VIC, Australia

OK It was the head gasket with a leak, so the next question, what can it cost to fix up the head gasket??

 

_________________

Jesus Drove Fords

Proud Owner of a XR6 MkII

Top
 Profile  
 
 
Posted: Thu Nov 17, 2005 12:01 pm 
Getting Side Ways
Offline
User avatar

Age: 37

Posts: 3186

Joined: 8th Nov 2004

Gallery: 6 images

Ride: EF Falcon

Location: Townsville
QLD, Australia

Oh man, thats a shame to hear.

When i was looking at a new head gasket, i was quoted between 800 and 1400 for an identical job.

Shop around

 

_________________

Nicco's M112 Blown, T-56 equipped EF
forums/viewtopic.php?t=68319

Top
 Profile  
 
 
Posted: Thu Nov 17, 2005 12:35 pm 
Getting Side Ways
Offline
User avatar

Age: 40

Posts: 927

Joined: 6th Nov 2004

Ride: BA Falcon EGas

Location: Perth
WA, Australia

Do it yourself for under $400 easily.
That money would include beer for the whole time you'd be doing it.

Its an easy job, just tedious.

My head gasket change cost me ~$550 and that includes a port and polish.

 

_________________

BA Falcon Futura on EGas. Stock as...

EF 5 speed manual; PH 4480 Pacemaker Headers; 2 1/2" Lukey Mandrel Bent System; Hi Flow Walker Cat; Stage 3 Crow Cam; ChipTorque Chip; 3" Mandrel Bent Intake; K&N Pod Filter; Low Pedders Suspension; 17" EL GT Champagne Rims; RPM Series Clutch

Top
 Profile  
 
 
Posted: Thu Nov 17, 2005 12:42 pm 
Smokin em up
Offline
User avatar

Age: 40

Posts: 237

Joined: 7th Jan 2005

Gallery: 3 images

Ride: BA XR6 Falcon

Location: Hawthorn
VIC, Australia

I have a feeling this is out of the depth of Knowledge though. Also would being the older 3.9EFI make it any harder or easier to do yourself?


Also I dont have the greatest tools to do it, only a couple of spanners and sockets, nothing really to pride myself on really............Does that make me less of a man.....*sobbing in the corner*

 

_________________

Jesus Drove Fords

Proud Owner of a XR6 MkII

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 2  [ 24 posts ]  Go to page 1, 2  Next

Who is online

Users browsing this forum: Google Adsense [Bot] and 59 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Sun Nov 24, 2024 10:37 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names