|
EB91XR6 |
|
|||
|
well i have tryed everything to start the ED that i have, i know it runs as i have driven it, it has sat down the driveway for 4 months while i convered it to manual, lowered it changed the rearmain seal and sump gasket all the coolent lines put a cam in it a 3.45 lsd and now it wont start,
so far i have cheeked smartlock is working timing is good redone myself its got spark its got fule starter motor is working well i just cant work it out iv even tryed putting fuel in the manafold and it wont start. tryed a new battery and that dosnt do anything, im offering a prize of a carton of beer of your choice to some one who can get it to run,
_________________ 1976 XC falcon
|
|||
Top | |
FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
have you checked for the proper voltage and signals at the appropriate ecu pins for your model?
|
||
Top | |
ReGiE |
|
|||
|
cam was put in a tooth or 2 out?
_________________ Gooooone - Eb2 Coon - 143RWKW |
|||
Top | |
RedRoo |
|
|||
Age: 55 Posts: 1883 Joined: 22nd Apr 2005 Ride: 94 ED Fairmont, MY97 LE WRX Location: Seymour |
Did you swap the wiring loom over when you did the manual conversion?
If so did you use the right manual ecu? (not a EF ecu?) If you kepted the Auto wiring did you do the modifocation to it correctly? Injectors are proberly blocked also. |
|||
Top | |
Krytox |
|
|||
|
dizzy 180deg out?
_________________ Carefree, we may not be number one, but we're up there. |
|||
Top | |
krisisdog |
|
|||
|
So it doesnt turn over at all? or it does just wont fire?
|
|||
Top | |
EB91XR6 |
|
|||
|
ok to answer some questions the manual convertion was done to my EB xr6 and the lume was made for it and have done the nutral safty switch,
the motor cranks but dosnt fire, the timing is set on the compretion stroke the cam was put in and the timing chain didnt move as i had 5 cable ties around it. i have done all the mods before to my eb fairmont and my EB xr6 and havent stuffed them up before. i have done a certifict 1 in mechanics, but i still cant work out the issue with this car, im stumped
_________________ 1976 XC falcon
|
|||
Top | |
phongus |
|
|||
|
Sure ECU is not buggered? Tried putting another ECU in?
phong =P~
_________________ phongus = Post whore 2006 |
|||
Top | |
gogetta |
|
|||
|
have you checked fuel pressure and ign timing with a timing light
_________________ |
|||
Top | |
EB91XR6 |
|
|||
|
have tryed the orginal ecu and the xr6 ecu no difference,
how do you cheek fuel presure, i have put fuel down the trought and no difference, and where do you get a timing light
_________________ 1976 XC falcon
|
|||
Top | |
gogetta |
|
|||
|
ok so regards fuel
have you check fuel pump and fuel relay are working (do u have a diagnostics connector in the fuses area?) u need to bridge some terminals to test the fuel electrical circuit...when u do this u should hear fuel flowing in the rail......see this thread http://www.fordmods.com/forums/viewtopi ... lay%20test then check that the injectors are pulsing (use test light or listen) for fuel pressure u need a guage and T it into the fuel supply line.. check ign timing with a timing light bought from supa cheap or bunnings
_________________ |
|||
Top | |
EL__Fairmont |
|
|||
|
Loosen the Dizzy and have someone try to start the engine while you advance the dizzy as far as it goes than try retard as far as it goes. See what happens if you can get it running then get a timing light on it.
I had this problem when I did the MPI conversion on a EA CPI falcon. Did everything right(top dead centre on no1 compression stroke etc) but there is 2 positions the dizzy will slot into that seem right. 1 cog out caused it to be retarded by a s**t. I fully advanced the dizzy and just got the car running under 3/4 throttle but nearly stalling. Checked the timing and the mark was right down below the a/c compressor. Pulled the dizzy back out slotted it in again and all good. Cheers.......
_________________ 97 EL Fairmont 4l OHC .Silver. |
|||
Top | |
frankieh |
|
|||
|
Quote: the cam was put in and the timing chain didnt move as i had 5 cable ties around it.
By 5 cable ties, I assume you mean you tied the chain to the sprocket, but did you keep the chain tight as well? If it gets loose, it could have slipped off down the bottom on the crank and be out a tooth. rgds Frank |
|||
Top | |
Falcon96kickass |
|
||
|
i know you said smart lock is working but try changing the bcm and check fuses if someone hasnt mensioned it yet
_________________ Your all a bunch of f**k Heads delete this f**k account stupid useless C*** who run this site cant even sell something useless wankers |
||
Top | |
EB91XR6 |
|
|||
|
i think its ether
new motor time or send it to the auto electrition
_________________ 1976 XC falcon
|
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 95 guests |