|
| gate_21 |
|
||
|
hey everyone, just putting my new harmonic balancer on. im trying to knock it into place with a hammer wrapped in a cloth but it doesnt seem to wanna move in line with the rest of the pulleys? needs to go back at least a cm and a bit. any tricks to doing this?
|
||
| Top | |
||
| crispy |
|
||
|
Can you get the bolt in enough to get it to take thread, maybe doing it up a little will help it move and tap it while under pressure of the bolt
|
||
| Top | |
||
| gate_21 |
|
||
|
nah cant get it that far...although its almost at the start of the thread
|
||
| Top | |
||
| gate_21 |
|
||
|
still not budging...been at it for a while now. didnt know they were so hard to put back on. any help anyone?
thnx |
||
| Top | |
||
| xfnoho |
|
||
|
you have lined up the keyway haven't you!!!!
|
||
| Top | |
||
| gate_21 |
|
||
|
is that the groove that it slots into? if so then yes i have done that =)
|
||
| Top | |
||
| crispy |
|
||
|
Hmm thats a pain, maybe try taking it off and putting it on again, check theres nothing on the surface or on the keyway
|
||
| Top | |
||
| gate_21 |
|
||
|
sure is a pain...really need 2 get this car bak on the road. gonna give it another go tomorrow. thnx for the replies so far
|
||
| Top | |
||
| aaron_hogan |
|
||
|
emery paper the internal surface of the balancer and around the keyway. Sounds like its nipping up on a burr. Also check the crank key for burrs and that it is seated fully in its slot. It may be seated incorrectly a little far back in the slot. Check it with a straight edge so its sitting paralel with the crank.
Use a little "anti-seize". Don't just use grease as grease can set hard. good luck
_________________ EA SVO Fairmont Ghia - Recaros, Bilsteins, Sunroof, SVO rims and body kit, Genie headers, DBA rotors. T5 steeda triax short shifter. 3.27 lsd. (EL 4.0 ported/polished, rebuilt and balanced, Dev5 cam. J3 chipped EL ecu, AU injectors). |
||
| Top | |
||
| gate_21 |
|
||
|
thanks alot everyone i got it back on. its almost in line now maybe a mm or 2 off. the way i got it on was by putting the bolt on without the washer ( because it wasnt catching the thread with the washer) and tightening it slightly. then i undid it and put the washer on with the bolt and just tightened it. took a bit of effort but it went on. started it up and the belt is not fully on the pulley that is above the harmonic balancer, but it will do for now. might have to put a washer behind it to make it sit right
|
||
| Top | |
||
| vibr8n |
|
|||
|
so it sits proud with the factory washer ? :S
you need to lock the balancer up to do the bolt up.
_________________ crow cam,cai,exaust,bbm,190 reg & el injectors,xr6 interior,guages,white cluster,pioneer/mtx stereo,big boot install w.i.p, 17"rims,koni/pedders shocks&springs with nolathane re-bush,ssv kit,stainless inserts,clear lights,t5 & short shifter,chardonay/pearl paint |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 72 guests |
