|
| Falcon_92_EB |
|
||
|
is the pcv or whatever it is supposed to go from the rocker cover to the idle controller?
Last edited by Falcon_92_EB on Wed Jul 08, 2015 10:45 pm, edited 1 time in total. |
||
| Top | |
||
| krisisdog |
|
|||
|
Yeh, something to do with how the lpg is setup.
|
|||
| Top | |
|||
| ausedwagon |
|
|||
|
its the crankcase ventilation so if there is lpg getting into the oil it goes back into the intake and not out into the air
_________________ 94 White ED Wagon |
|||
| Top | |
|||
| TROYMAN |
|
||
|
yes its there because it has lpg..
|
||
| Top | |
||
| Auturbo6 |
|
|||
|
It's there to prevent LPG from entering the Sump and potentially blowing the sump off.
Im a Taxi mechanic and i've seen it happen. On a petrol falcon the PVC hose enters under the trottle body potentially allowing LPG to enter the engine. Hope this helps.
_________________ This is all u'll ever see... |
|||
| Top | |
|||
| Falcon_92_EB |
|
||
|
then there is 1 small problem
i have put a new idle speed controller and it dosent have the hose connection on it |
||
| Top | |
||
| TROYMAN |
|
||
|
lukas_bartko wrote: then there is 1 small problem i have put a new idle speed controller and it dosent have the hose connection on it its a plastic plate that goes in between the isc and throttle body... you just need to re fit it under the isc |
||
| Top | |
||
| Falcon_92_EB |
|
||
|
no its not the old isc had a hole drilled into it and a hose connection screwed in!
|
||
| Top | |
||
| dsyfer |
|
|||
|
lukas_bartko wrote: no its not the old isc had a hole drilled into it and a hose connection screwed in! Any LPG place should be able to sell you the little plastic spacer to attach the hose to. |
|||
| Top | |
|||
| TROYMAN |
|
||
|
hmmm ok..
well there is normally a plastic plate that goes in between.. someone has drilled and taped in a fitting instead of the plate.. you can get a plate from a lp gas fitter, i know ford sell them for the au's.. |
||
| Top | |
||
| Falcon_92_EB |
|
||
|
o thanks troyman!
Last edited by Falcon_92_EB on Wed Jul 08, 2015 10:45 pm, edited 1 time in total. |
||
| Top | |
||
| LP_ |
|
||
|
TROYMAN wrote: hmmm ok..you can get a plate from a lp gas fitter, i know ford sell them for the au's.. The AU plate from Ford is the right one to buy for an EF/EL engine and its not expensive to buy from Ford |
||
| Top | |
||
| Falcon_92_EB |
|
||
|
i brought the au pcv plate for the gas but the bolt holes didnt line up so had to "edit" it a bit but works good thanks troyman and LP_
didnt line up because it was for my ef i think au's are differnt slightly |
||
| Top | |
||
| TROYMAN |
|
||
|
yea you need to drill the holes in the plate to use the au one on an ef..
i found out that there is one available for the ef/el from ford but at $70 , best off getting the $20 au one and drill it out.. |
||
| Top | |
||
| Falcon_92_EB |
|
||
|
$70 !!!!!
 what a rip i guess thats why some of you guys call it fraud 
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google [Bot] and 117 guests |
