|
| [SH4UN0] |
|
|||
|
hey there guys after the lastest fordmods event at heathcort drags which was a night to remember and my first time down the strip. for a stock EA i pulled out a 16.72 witch i like for now.
i have decided to make some mods to the car as soon as i have the $$$ the mods that i will be getting are : 1. K & N filter 2. larger snorkle for better air flow into the engine 3. cam 4. Extractors 5. 2.5" mandrel bent / mild steel catback zorst that would bolt straight up to yours if you are interested - BA XR tip on the end ( that im getting off dcstraight, once again thanks buds ) if you guys thinks that im missing anything that would be good plz let me know
_________________ The Ute's Numbers
|
|||
| Top | |
|||
| eed-250 |
|
||
|
scrap all those ideas and get a manual conersion You should be able to get a manny for under 1k installed.
A manual conversion will make more difference then all those mods combined 
|
||
| Top | |
||
| twr7cx |
|
|||
|
check out the sticky in this thread and do a search and you should find plenty plenty of infor!
|
|||
| Top | |
|||
| downingj |
|
||
|
eed-250 wrote: scrap all those ideas and get a manual conersion You should be able to get a manny for under 1k installed.
A manual conversion will make more difference then all those mods combined Well said. OR save your cash for a complete engine swap??? But yeah, realistically, the manual conversion will be your best bet 
|
||
| Top | |
||
| Southy |
|
|||
|
i have Cam, zauhst, headers, and a few more little things done and managed to pull a 14.8
|
|||
| Top | |
|||
| [SH4UN0] |
|
|||
|
its already a manual, soo now just got to get them mods and should be all sweet.
by the way southy after i get them done we will have to compare times down the strip.
_________________ The Ute's Numbers
|
|||
| Top | |
|||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
is the engine shagged??
i would have thought you would be at least in the very low 16 to very high 15s with a 5 speed. |
||
| Top | |
||
| [SH4UN0] |
|
|||
|
ive got the extra weight of a gas tank that was full at the time of the drags, as far as i know the clutch is slipping and the engine is fine
_________________ The Ute's Numbers
|
|||
| Top | |
|||
| smoke_ |
|
|||
|
what was the 60ft time like?
you should be able to run closer to a flat 16 with an ea s-pack i would think.
_________________ NEW RIDE - FPV FG F6 6spd Auto. 12.26@114MPH, 1.88 60FT on Cheapy Tyres with 38PSI - Stock except K&N filter! |
|||
| Top | |
|||
| [SH4UN0] |
|
|||
|
60ft time was 2.5 seconds
_________________ The Ute's Numbers
|
|||
| Top | |
|||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
[SH4UN0] wrote: ive got the extra weight of a gas tank that was full at the time of the drags, as far as i know the clutch is slipping and the engine is fine
so you did those times on gas? or on petrol with the gas system all there? either way not bad times considering |
||
| Top | |
||
| [SH4UN0] |
|
|||
|
on petrol with the gas system all there
_________________ The Ute's Numbers
|
|||
| Top | |
|||
| eed-250 |
|
||
|
my mates EA 5spd ran a 15.9 when he had exhaust and extractors.
He put a volvo thermofan on her, spooled hte diff and ran a 14.7 lol now he has an 11second vn 
so spool your diff mate.. and get rid of the petrol system. Convert her to all gas! |
||
| Top | |
||
| eed-250 |
|
||
|
oh he also a ran a pod filter aswell.
|
||
| Top | |
||
| [SH4UN0] |
|
|||
|
ive got more power on the pertol than i do on the gas, first ill do these mods and see how she runs and if it pisses me off i remove the lpg
_________________ The Ute's Numbers
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 117 guests |
12.06@120MPH