|
| Crazy6ltr |
|
|||||
|
Heay all my EB sedan Motor has done roand abouat 390,000 on the clock and i want to ether rebild or replace.cheak out how bad it looks.
Attachment: Picture 0122.jpg [ 142.31 KiB | Viewed 163 times ] Attachment: Picture 0142.jpg [ 184.2 KiB | Viewed 159 times ]
_________________ Car got Crushed |
|||||
| Top | |
|||||
| 93EB |
|
|||
Age: 47 Posts: 2485 Joined: 6th Oct 2005 Ride: 93EB Fairmont / BA Falcon XR6T Location: Western Sydney |
Does the engine still run OK ? My EB has the same kays and still goes strong, has no bottom end noise and does not eat oil. With your engine its nothing a can of degreaser or 2 wont fix.
_________________ 93 EB II Fairmon8 with 17' EL GT's / Clear indicators / H.I.Ds / Sports exhaust / Lowered 2' / K&N / XR6 ECU. |
|||
| Top | |
|||
| Crazy6ltr |
|
|||
|
well it runs good in terms of power (cant have much as a P plater) but it over heats after about 2 hours of constant driving and it's got a bad tiking niose at low RPM, but it's got a Brand new manifold and snorkle box, so dats still alright
_________________ Car got Crushed |
|||
| Top | |
|||
| frd906n |
|
||
|
This thread should be in the 6 cylinder section not in exterior modifications area,
Just get a 2nd hand engine and rebuild, that way you still driving the car, then find a good time and place to swap it over. should take about couple of days. Ticking, If you have ticking noise means thats your lifters in the head are on there way out or the oil pressure, Over heating. Has it had a engine flush if not, give it one, should fix the overheating problems
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| TROYMAN |
|
||
|
moved to 6 cyl forum
|
||
| Top | |
||
| Crazy6ltr |
|
|||
|
hay thanks for the replys so it's the lifters ay bugger and im not worroed about taking her of the road for a while as ive got my wagon as for serviceing, ford gave it he full works 3 moths ago (trans flush, engine oil, filters, timing) for like 190 bucks so yer bugger
_________________ Car got Crushed |
|||
| Top | |
|||
| XRfairmont67 |
|
|||
|
a set of brand new lifters will cost between $8 -$12 ea and u need 12 of them. not too hard to do. also grab a set of rocker cover bolt grommets and that will fix the rocker cover leaks and a tin or 2 of $2 degreaser.
get a mechanically minded mate to help u, do some research here and u should get it done in under a couple of hours. |
|||
| Top | |
|||
| Crazy6ltr |
|
|||
|
hey all theanks for the tips. i just got back from super cheap with 5 cans of degreasher for $10 and ill spray that on after my dad rebilds it(he's a air force mecanic so he knows his s**t)
and ill take pics after, it should only take a week or 2 Laterz
_________________ Car got Crushed |
|||
| Top | |
|||
| 93EB |
|
|||
Age: 47 Posts: 2485 Joined: 6th Oct 2005 Ride: 93EB Fairmont / BA Falcon XR6T Location: Western Sydney |
Gees your dad must be easily over 100 and doing alright for his age considering your 76.
_________________ 93 EB II Fairmon8 with 17' EL GT's / Clear indicators / H.I.Ds / Sports exhaust / Lowered 2' / K&N / XR6 ECU. |
|||
| Top | |
|||
| DARTHVADER |
|
|||
|
93EB wrote: Gees your dad must be easily over 100 and doing alright for his age considering your 76. LMAO MITCHY
_________________ AUIII, PACEY 4499's, MAGNIFLOW CAT, 2.5" ZORST, 17X8" AUII XR RIMS....otherwise all factory! |
|||
| Top | |
|||
| Crazy6ltr |
|
|||
|
Yer haha verry funny. now peaple i fuked that up when i sighned up
 , im actuly 17 so mehBut any ways ig called up a head shavers joint and thay said thay would shave of 2.7mm of the bore and head and fit stronger pistons for $600 .also i can get a brand new crankshaft of a VCT au III for $120 and my mate's uncle can paint my rocker cover for free so im FUKIN LAUGHIN 
_________________ Car got Crushed |
|||
| Top | |
|||
| cjh |
|
|||
|
Crazy6ltr wrote: hey all theanks for the tips. i just got back from super cheap with 5 cans of degreasher for $10 and ill spray that on after my dad rebilds it(he's a air force mecanic so he knows his s**t) and ill take pics after, it should only take a week or 2 Laterz Air force mechanic, eh?.....knows his LR 110's and Cessna's.........LOL........pullin ya leg.....
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| frd906n |
|
||
|
After he rebuilds it it should fly away among the clouds
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 87 guests |
