|
| jpiez |
|
||
|
hey im new to this forum n im wondering that i best mod to do next woud b... i hav a series II Eb manual, with big cam(adjustable timing gear), port n polished head, extractors + full exhaust, 3.45lsd(for sale tho) raised compression. wot would b the next best mod to do??
thanks jim
_________________ EF futura manual, JMM cam, rollmaster adjustable timing gear, JMM port n polished head, extractors + full exhaust, lock rite LOKKA, raised compression, tinted windows, 17inch au xr tickford rims, LOW, 3inch CAI, sunroof, genuine tickford bodykit. NOW WITH 142RWKW |
||
| Top | |
||
| ElwoodBlues |
|
||
|
Your brakes
_________________ EF Futura factory 5 spd
|
||
| Top | |
||
| jpiez |
|
||
|
yer they r gettin there... what next should b done that will get the car movin quicker??
_________________ EF futura manual, JMM cam, rollmaster adjustable timing gear, JMM port n polished head, extractors + full exhaust, lock rite LOKKA, raised compression, tinted windows, 17inch au xr tickford rims, LOW, 3inch CAI, sunroof, genuine tickford bodykit. NOW WITH 142RWKW |
||
| Top | |
||
| MYLO_XR6 |
|
||
|
the list goes on forever, what compresion ration you running at?? probably sneak it up to 12:1 (after your head has been blueprinted, then for about a grand, you can install water injection system which will prevent pre-ignition....no 12:1 isnt too high for standard pistons, as long as your head is blueprinted and water injectection is installed.....think about it, the smaller the area, the louder the POP
_________________
|
||
| Top | |
||
| fordfreak ef |
|
|||
|
unichip or another type of aftermarket ecu to tune the air/fuel ratio's n dail the cam in properly...
|
|||
| Top | |
|||
| Southy |
|
|||
|
TURBO
|
|||
| Top | |
|||
| Steady ED |
|
|||
|
fordfreak ef wrote: unichip or another type of aftermarket ecu to tune the air/fuel ratio's n dail the cam in properly...
Another vote for that 
Which JMM 'Dev' head and cam is it?
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| TwinturboBMX |
|
|||
|
Yeah some form of forced induction id say.
_________________ 17" Tezza Steelies, King F**king lows, pedders sports ryders, 2.5" cat back exhaust, pacemaker extractors, T5 manual
|
|||
| Top | |
|||
| XITED6 |
|
||
|
3:9 gear ratios in the a**
_________________ AU II XR6 Hp 5 Speed. |
||
| Top | |
||
| haggis |
|
|||
|
Nice big intake, beefier injectors, stand alone engine management.
Short of removing the rev limiter and using a proper ECU to let the engine rev higher im not sure there are many other ways you could get more power N/A ?
_________________ I can see through wooden doors. |
|||
| Top | |
|||
| senna*xrt |
|
|||
|
Suspension work, you can lose heaps of speed if the car can't get away cleanly, also agreed on brakes and ECU
_________________ my car caught a cold, now it sneezes!
|
|||
| Top | |
|||
| brendo_83 |
|
||
|
I think you've covered all the reasonable priced NA mods.
its the law of diminishing returns, you'll have to spend big dollars to get any significant increase. I'd say bit the bullet and go turbo, for the money you'll end up spending in NA mods you'll get more go from a good turbo setup. |
||
| Top | |
||
| HJThew |
|
|||
|
Save your cash, sell the old taxi and get yourself a BA XR6.
|
|||
| Top | |
|||
| efbignik |
|
|||
|
injectors
brakes ecu NOS
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| Aaron_EF8 |
|
||
|
MYLO_XR6 wrote: the list goes on forever, what compresion ration you running at?? probably sneak it up to 12:1 (after your head has been blueprinted, then for about a grand, you can install water injection system which will prevent pre-ignition....no 12:1 isnt too high for standard pistons, as long as your head is blueprinted and water injectection is installed.....think about it, the smaller the area, the louder the POP
What the f**k?! How do you blueprint a head, and how will it effect compression ratios? You obviously have no understanding of compression ratios either, to get a 4.0 to 12:1 with stock pistons is impossible. The head has to have a combustion chamber, you can't mill it until its level with the valves, what about valve-piston clearance? You forgot to mention about cam journals, the extra timing chain length, water jacket differences, head bolts bottoming out, just to name a few. I think you have just made everone who has read this post a little stupider. I'm not going out of my way to attack you personally, but when people like yourself write complete s**t on the forums, sometimes inexperienced people who don't know better will think what you said is right, when it isn't. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 75 guests |
