Fordmods Logo

No idle after engine swap. 

 

Page 1 of 1 [ 7 posts ] 

 
 Post subject: No idle after engine swap.
Posted: Thu Jan 03, 2008 3:03 am 
Getting Side Ways
Offline
User avatar

Age: 52

Posts: 3424

Joined: 23rd Dec 2007

Gallery: 32 images

Ride: BA XR6T (mix of BA, BF and FG)

Location: Perth
WA, Australia

Hi everyone...

I fired up the new motor today.. it had not been run for 3 months and the oil had gunked up a bit, so replaced the filter and put diesel oil in it so the detergents can clean it up before another oil and filter change in a couple of hundred km.

Anyway, onto the problem.. she fired up nicely... but won't idle at all... ran smoothly.. but as soon as you took the foot off the gas... she dies.

in the "common problems" tech doc.. it details an idle speed controller... but that tute appears to be EF/EL related and doesn't look anything like the ED motor... I'm assuming it does have one... but where is it?

Also is there anything else I should look at to determine the idle.??
my old motor idled perfectly... so unless I forgot a plug somewhere, it's not electrical.


any suggestions would be fantastic.


rgds

Frank
Top
 Profile  
 
 
Posted: Thu Jan 03, 2008 9:54 am 
Fordmods Junkie
Offline
User avatar

Posts: 11752

Joined: 17th May 2005

Gallery: 11 images

Ride: EL Fairmont, VFR400 racer

Power: 144 rwkw

Location: Melbourne
VIC, Australia

Try cleaning out the Throttle body as well. ISC should be near the TB if the EDs had one, but i assume all of them had an ISC.

There may also be a vacuum leak somewhere. Could have missed a hose that was meant to be on. Check the MAP if the hose has come off. I would say timing but that should be checked last.

Also...the computer has to relearn everything, so hopefully in time it will fix itself.

phong =P~

 

_________________

phongus = Post whore 2006
EL XR6 motor, EL ECU + J3 chip, WADE 1673 Camshaft, 3" S/S intake, Pacy 4480, 2.5" Hi flow cat, 2.5" Lukey exhaust.
Max Power = 144.6 rwkw (03/05/2008)

Top
 Profile  
 
 
Posted: Thu Jan 03, 2008 12:49 pm 
Getting Side Ways
Offline
User avatar

Age: 52

Posts: 3424

Joined: 23rd Dec 2007

Gallery: 32 images

Ride: BA XR6T (mix of BA, BF and FG)

Location: Perth
WA, Australia

OK, will check it out...

thankyou.

rgds

Frank
Top
 Profile  
 
 
Posted: Thu Jan 03, 2008 1:52 pm 
Getting Side Ways
Offline
User avatar

Age: 52

Posts: 3424

Joined: 23rd Dec 2007

Gallery: 32 images

Ride: BA XR6T (mix of BA, BF and FG)

Location: Perth
WA, Australia

Actually, it must have been just the computer...

started it again this morning and it idled.

The oil light is on though, despite the smooth noise free operation,, so going to check the sender is plugged in.
Top
 Profile  
 
 
Posted: Thu Jan 03, 2008 10:11 pm 
Getting Side Ways
Offline
User avatar

Age: 52

Posts: 3424

Joined: 23rd Dec 2007

Gallery: 32 images

Ride: BA XR6T (mix of BA, BF and FG)

Location: Perth
WA, Australia

Ok. The idling is intermittent... it isn't idling now.



The oil light turns out to be simple.. the old Fairmont motor just had an oil light.. the new one must have had an oil pressure guage... so have to swap out the sender unit.


Dunno what to do about the idle yet.
Top
 Profile  
 
 
Posted: Fri Jan 04, 2008 7:51 am 
Stock as a Rock
Offline

Posts: 125

Joined: 2nd Dec 2007

Location: bellbrook
NSW, Australia

vacuum house?
Top
 Profile  
 
 
Posted: Fri Jan 04, 2008 8:16 am 
Fordmods Newbie
Offline

Posts: 12

Joined: 22nd Dec 2007

Location: Gladstone
QLD, Australia

I had the same problem with my ED after I changed the battery, it turned out to be the TPS or throttle positioning solenoid. there is a procedure to rectify this but I can't remember it accurately best ring ford or racq they might be able to tell you over the phone.
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 7 posts ] 

Who is online

Users browsing this forum: Google [Bot] and 74 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Thu Nov 28, 2024 7:48 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names