|
| THEBOSS |
|
|||
|
Just finished putting in the el engine in my ea. Connected battery back up. Acc lights come on when key is turned, and then nothing.... No starter motor turning, fuel pump does start cause i can hear it.... but nothing, no spark, no crank.... must be wiring im assuming... anyone else had this problem when doing an engine conversion.,.. Someone help cause im P**sed off and outta ideas...
|
|||
| Top | |
|||
| Froudey |
|
||
|
checked looms etc are you using the log manifold? with ea ecu or el ecu????
_________________ R.I.P Tobias my son. |
||
| Top | |
||
| phongus |
|
|||
|
Are the battery terminals in good condition and are all the Earth wires re earthed?
If not does it have smart lock (I know it's an EA but not sure if you changed anything else over). You may need to bypass it. phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| THEBOSS |
|
|||
|
EA loom with EL ECU. Already bypassed smartlock... and checked all earths...
|
|||
| Top | |
|||
| THEBOSS |
|
|||
|
using bbm and battery terminals are fine...
|
|||
| Top | |
|||
| phongus |
|
|||
|
How about the auto? 3 speed or 4 speed?
may need to do a resistor trick if you have a 3 speed or manual. Sorry just taking possible stabs here. phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| THEBOSS |
|
|||
|
no problem phongus... it s a 5spd manual... i done the resistor trick already and to my knowedge all done correctly.... strange thing is accesory lights come on.... but go to turn it and it doesnt do anything. at one stage the rev tacho went to 6K then back to 0rpm... hmmm.... so frustrating...
|
|||
| Top | |
|||
| phongus |
|
|||
|
Have you checked the ignition relay or maybe your ignition barrel. How is the charge on the battery?
Currently at work, so I can't think of a list of things that might happen...if something pops up i'll keep posting  .
phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| cjh |
|
|||
|
The main relay, is it working???? Theres two together, a green one ( fuel ) and the brown one ( main ). Just near the coolant bottle.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| grub73 |
|
|||
|
Double check the wires to the starter?? try shorting out the starter with a scewdriver (with car in neutral) to see if there is any kick. If not try a test light to see if you have power at the main lead at the starter, if you have, then get someone to turn the key while you check for power at the starter trigger/soleniod wire.
_________________ EF XR6 5spd 14.57@97mph |
|||
| Top | |
|||
| THEBOSS |
|
|||
|
fixed... had wrong wire onto starter motor.... but anyways which pin does the thermo fans go into on the EL ECU... i tried both pin 33 and 53 but none activated the thermo's....hooked them up properly coz tested using the relays straight to battery and they turned on.... its earthed properly as well.... not sure which pin triggers the relay...???
|
|||
| Top | |
|||
| THEBOSS |
|
|||
|
by the way thanks everyone the help.... im running both fans off two relays but got it hooked up running in parallel so only one trigger wire instead of using pin 33 and 53 im only using one or the other...
|
|||
| Top | |
|||
| phongus |
|
|||
|
Good to hear you got it sorted...it's the little mistakes that cause a lot of havoc lol. I found that out the hard way all the time.
Sorry can't help you with the Thermos though...I'm sure someone else can. phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| THEBOSS |
|
|||
|
i know itse little mistakes that really annoy u but at least its easy fixed... yeah im not sure on the trigger wire...when i power the relays straight from the battery the fans tecu urn on... but when the fans are connected to the (pin 33) the fans dont come on... even at operating temperature which i think is about 100 degrees.. i know its running at 100 degrees coz the temp sensor is reading a 0.5V which from wat i understand is 100... just neeed to kn how the thermo's are triggered... which wire which pin really...???
|
|||
| Top | |
|||
| TROYMAN |
|
||||
|
hi
pin 53 is to trigger both fans on low. and pin 33 is to trigger the relay for fans on high..(possibly for when aircon is triggered) or engine temp reaches 100+ deg but i had issues with pin 33 no trigger.. so the fans would only come on low and they would not go to high when the aircon was turned on or the temperature was high.. but if your going to run the fans on full speed pin 53 should trigger the fans when the temp gets between 1/4 and 1/2.. but if you have working aircon you need to have a trigger to switch the fans on or you will cook your air con..you can test pin 33 and see if it triggers when the aircon is switched on. or you can add a seperate relay to overide the ecu trigger so when your aircon is on the fans are also on... this is the diagram i used when i tried to hook mine up.. but in the end i just used a davis craig thermal switch to trigger the fans instead..
|
||||
| Top | |
||||
| Who is online |
|---|
Users browsing this forum: No registered users and 53 guests |
