|
| ea_falcon |
|
||||
|
ended up with these parts after putting the head back on
any idea where they go or can someone point me to a picture that shoes where they go. The car is a 6 cylinder el
_________________ 02 series 3 AU marline ute 5speed 347 stroker |
||||
| Top | |
||||
| krisisdog |
|
|||
|
Bolt looks to be one from the power steer bracket, and the other thing is a support for the BBM.
How big is the bolt? |
|||
| Top | |
|||
| bry40l |
|
|||
|
The throttlebody has a bracket that goes from I think the inlet manifold to the throttle bdy maby thats it I forget wat it looks like
_________________ BF XR6 |
|||
| Top | |
|||
| ea_falcon |
|
||
|
yeah that bracket does look like its a bbm support...just dont know where abouts it goes....its underneath somewhere? hard to see.
the bolt is 9.5cm long
_________________ 02 series 3 AU marline ute 5speed 347 stroker |
||
| Top | |
||
| phongus |
|
|||
|
ea_falcon wrote: yeah that bracket does look like its a bbm support...just dont know where abouts it goes....its underneath somewhere? hard to see. the bolt is 9.5cm long Bracket looks like the throttle body to manifold/head support. It sits on the side facing the front of the engine and angles forward. The bolt might be the one that holds the alternator support bracket/pole/stabilizer bar to the head. The pole/stabilizer bar/whatever you call it, goes from the top of the alternator to the head. Only other thing I can think of is water pump bolts...but doubt you removed the water pump...
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| XRfairmont67 |
|
|||
|
the bracket bolts on the bottom of the throttlebody just above the air intake temp sender, the other end goes to the top manifold bolt just infront of number 3 injector.
when you put the intake bolts back in, did you notice one was about 5mm longer than the rest? this allows for the width of the bracket. the other bolt goes in the bottom hole of the power steer bracket, goes through the timing cover and into the block, also goes though the brace from off the top of the alternator . this bolt leaks oil if you dont put silicon on near the head of the bolt |
|||
| Top | |
|||
| phongus |
|
|||
|
XRfairmont67 wrote: the bracket bolts on the bottom of the throttlebody just above the air intake temp sender, the other end goes to the top manifold bolt just infront of number 3 injector. when you put the intake bolts back in, did you notice one was about 5mm longer than the rest? this allows for the width of the bracket. the other bolt goes in the bottom hole of the power steer bracket, goes through the timing cover and into the block, also goes though the brace from off the top of the alternator . this bolt leaks oil if you dont put silicon on near the head of the bolt Brace...that's what it's called.
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| madeaspack |
|
||
|
looks like stage 1 weight reduction to me
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| ea_falcon |
|
||
|
cheers for the replies...will check it out tomoro
_________________ 02 series 3 AU marline ute 5speed 347 stroker |
||
| Top | |
||
| Benny D |
|
|||
|
lol.. i always end up with spare nuts and bolts.. sometimes worrying but iv never had anythin go wrong yet..
_________________ BA XT V8. Ice Mint. 18" Speedys. XR6T LSD. Full Pacemaker twin 2 1/2inch Stainless Steel system. Custom CAI. Black XR interior with white trimming. Powerbond underdrive kit 25%. |
|||
| Top | |
|||
| ea_falcon |
|
||||
|
Thanks guys for the responses was realy helpfull...I have put the bracket on but i cant seem to find where the long bolt goes heres a pic of the front bracket on the power steering pump.
_________________ 02 series 3 AU marline ute 5speed 347 stroker |
||||
| Top | |
||||
| ea_falcon |
|
||
|
does the long bolt go on the bottom of this bracket? if so where does the bolt that i have there go?
is the alternator bracket bolted onto the wrong position?
_________________ 02 series 3 AU marline ute 5speed 347 stroker |
||
| Top | |
||
| ea_falcon |
|
||
|
does the long bolt go on the bottom of this bracket? if so where does the bolt that i have there go?
is the alternator bracket bolted onto the wrong position?
_________________ 02 series 3 AU marline ute 5speed 347 stroker |
||
| Top | |
||
| phongus |
|
|||
|
ea_falcon wrote: does the long bolt go on the bottom of this bracket? if so where does the bolt that i have there go? is the alternator bracket bolted onto the wrong position? The other end of the brace should be bolted to the top of the alternator I believe, using the alternator bolt. It isn't as long as the on pictured. Could it be one of the tensioner bolts? I think there are 3 bolts on the belt tensioner.
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| krisisdog |
|
|||
|
I'm guessing its a 10mm bolt head?
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 123 guests |
