|
| lowie57 |
|
|||
|
fairmont54 wrote: im in wodonga vic but mjr is in albury nsw 711 drome street its the border but i have a au belhousing 50$its yours Any chance you could post it somehow? i will buy it off you if you can. 4 hour drive is a bit out of the way for me lol |
|||
| Top | |
|||
| fairmont54 |
|
||
|
thats more than understandble i wil message you my phone number give me a call well sort it out
|
||
| Top | |
||
| lowie57 |
|
|||
|
fairmont54 wrote: thats more than understandble i wil message you my phone number give me a call well sort it out sounds good mate, I will probably call you tomorrow. Roughly whats the dimensions of a bell housing? |
|||
| Top | |
|||
| fairmont54 |
|
||
|
abot 80cm or so why is that?
|
||
| Top | |
||
| lowie57 |
|
|||
|
fairmont54 wrote: abot 80cm or so why is that? just wondering it it could fit into some kind of box for post, but yea ill call you tomorrow |
|||
| Top | |
|||
| lowie57 |
|
|||
|
i just found this on ebay
http://cgi.ebay.com.au/FORD-TICKFORD-EF ... 4a9c8ecf58 EF Tikford with 95,000k's. The guy says the lifters are a little rattly probably because its been sitting for 4-5 months without use, doesnt really bother me because i would swap over my reco AU head onto it anyway. What do you guys think? |
|||
| Top | |
|||
| TimmyA |
|
|||
|
still need to take out cam angle sensor and replace with a dizzy and change over the engine loom to suit, don't need a modified sump then, or au bell housing... Would be much simpler...
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| TROYMAN |
|
||
|
the ebay engine is from a 97 xh/el so it will already have a dizzy..
|
||
| Top | |
||
| lowie57 |
|
|||
|
ah ok, it was taken out of an XH, so that has different looms? does my el have a dizzy or coil pack? dunno if im making any sense lol
|
|||
| Top | |
|||
| lowie57 |
|
|||
|
TROYMAN wrote: the ebay engine is from a 97 xh/el so it will already have a dizzy.. Thats good to know, so its just the loom then? or is it the same loom? |
|||
| Top | |
|||
| TROYMAN |
|
||
|
lowie57 wrote: ah ok, it was taken out of an XH, so that has different looms? does my el have a dizzy or coil pack? dunno if im making any sense lol el has a dizzy..(ef has coil pack) im not 100% on the loom but its not difficult to swap the manifold loom from yours to that... |
||
| Top | |
||
| lowie57 |
|
|||
|
ok might seem like a silly question to most, but how would i go about transporting the engine to someone who can fit it?
|
|||
| Top | |
|||
| TimmyA |
|
|||
|
would be the same... only differences are EF is a coil pack set up then EL went back to dizzy then AU went to coil packs again
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| TimmyA |
|
|||
|
6x4 box trailer... old tire in the bottom stand sump up in the tired strap motor upright... thats how dad use to transport them...
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| alfy12 |
|
|||
|
Yeh, thats how I got my AU donk home from Shepperton. Works well. Also if you get an AU series 2/3 donk, you will have to fit your old EL engine mounts. The centre stud on the underside of the rubber mount will fowl on the hole in the mounting point if not changed. Series 1 engine mounts are the same as EF/EL so no dramas.
_________________ NF Fairlane: Non Factory Dual Fuel - New coolant tank, New fuel injectors, New fuel pump, New earth cable, ECU capacitors replaced, New O2 sensor, leads and plugs, New Radiator/Condensor cleaned. 483,000kms. AU I6 Powered. Struts, Shockies, Tie rods and ball joints replaced. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 35 guests |
