|
| ryanalder |
|
||
|
how hard is it to remove the upper half of the broad band mainyfold just wondering cause i thinking bout polishing it and also is it worth the effort?
|
||
| Top | |
||
| dsyfer |
|
|||
|
You need a long allen key to remove the top half, it is worth it, but it is a lot of work, be ready for a number of days work and lots of wet & dry paper.
|
|||
| Top | |
|||
| pissed'N'broke |
|
|||
Age: 38 Posts: 251 Joined: 9th Sep 2009 Ride: ED falcon gli - XR6 replica Location: Canberra |
only polishing the top? also have to sand if smooth before you can really polish it. many posts about this already. check KWIKXR's garage build i believe he has some pics etc
_________________ Ford ED Falcon Gli, T5 conv, Twinlight lights, exedy sports tuff clutch, modified EA front grill, ED XR6 complete interior, 19" speedy graphites, monroe gt shocks, kingspring superlows, CAI, ported tickford head, 3:45 LSD. |
|||
| Top | |
|||
| EL__Fairmont |
|
|||
|
I was always led to believe?? that they rough up the insides of the intake manifold to create better air turbulence for fuel/air combustion in the head????
_________________ 97 EL Fairmont 4l OHC .Silver. |
|||
| Top | |
|||
| phongus |
|
|||
|
I think it is wise to replaced the gasket between the top and bottom manifold halves once you remove the top from the bottom. I don't think it will seal properly once it has been removed and you will get leaks. But you can try without replacement...I didn't replace mine and I think it has a tiny leak...
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| KWIKXR |
|
|||
|
EL__Fairmont wrote: I was always led to believe?? that they rough up the insides of the intake manifold to create better air turbulence for fuel/air combustion in the head???? I believe he is talking about polishing the outside of the BBM as to get more engine bay bling  It's pretty simple to remove, just a whole heap of hex bolts you need to remove, a few hoses you need disconnect etc and it will come off. Takes a lot of grinding and sanding before you get anywhere near the polishing step. Definitely worth it in the end if you take your time and get a good finish. Might pay to get a spare BBM to polish up and when the time comes to put it on, you can just swap them over. http://www.fordmods.com/ford-interior-f14/polishing-bbm-t86304.html?hilit=BBM%20polishing And yes, it does pay to change the gasket while it's off to ensure a better seal between the surfaces. On the numerous occasions mine has been off i haven't yet changed from the original steel gasket Ford use so it's due for a swap next time it comes off 
|
|||
| Top | |
|||
| EDXR6-Poly |
|
|||
|
just curious do you get the gasket for the BBM in the middle in a VRS kit?
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| KWIKXR |
|
|||
|
EDXR6-Poly wrote: just curious do you get the gasket for the BBM in the middle in a VRS kit? Yes they should have one included. |
|||
| Top | |
|||
| BenJ |
|
||
|
Not for the BBM upper gasket. The gasket in the VRS is for the manifold to head gasket.
BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| KWIKXR |
|
|||
|
BenJ wrote: Not for the BBM upper gasket. The gasket in the VRS is for the manifold to head gasket. BenJ That's strange. Typically a VRS kit is a full top end kit. I know the "Permaseal" VRS kits include them. I've still got the BBM upper gasket from the Permaseal kit sitting here in fact ..
|
|||
| Top | |
|||
| BenJ |
|
||
|
There is no need to take the BBM apart when doing a VRS service, so hence, no gasket.
BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 102 guests |
