|
| LoganNZ |
|
||
|
I replaced the inlet manifold gasket on my '95 EF Fairmont on the weekend.
After reassembling everything, test-running, then test driving, everything was A-okay. But this morning, there is a huge fuel leak coming from between the fuel rail, and the fuel reg. I did unbolt the fuel reg during the manifold job. I there some special technique or trick to re-seating the fuel reg? Might I have buggered the seal? Any advice on this one much appreciated, before I start pulling things apart. There's too much fuel dribbling out to drive or start safely. Help!
_________________ Previous cars: |
||
| Top | |
||
| razza01 |
|
||
|
Hi mate, there is a o ring on the regulator that might have split or broken. I always replace them if dismantled and refit making sure you smear oil or grease on the rubber o ring for easy fit. Good luck
|
||
| Top | |
||
| LoganNZ |
|
||
|
Thanks man, yes that's exactly what it was - had gotten pinched and slightly torn when it was reinserted.
But guess what? Checked with Ford and it's an obsolete part?!? Ended up having to scrounge one off a wrecker down the road so I could drive home tonight.
_________________ Previous cars: |
||
| Top | |
||
| razza01 |
|
||
|
You can buy aftermarket units if you have no luck.
|
||
| Top | |
||
| razza01 |
|
||
|
should have said just a new o ring from repco.lol Do that to the old one for a spare.
|
||
| Top | |
||
| LoganNZ |
|
||
|
razza01 wrote: should have said just a new o ring from repco.lol Do that to the old one for a spare. Went to Repco, they didn't have any (at the store I went to). I live in Auckland. Maybe other Repco or Supercheap stores might have had them. I'm very surprised Ford have made a part like that obsolete already. Absurd. What next, EF brake pads?! The car cranks longer now before firing on start up, seems to be taking longer to build correct fuel pressure. Wondering what could have changed since I had all the injection system undone?
_________________ Previous cars: |
||
| Top | |
||
| TROYMAN |
|
||
|
LoganNZ wrote: razza01 wrote: should have said just a new o ring from repco.lol Do that to the old one for a spare. Went to Repco, they didn't have any (at the store I went to). I live in Auckland. Maybe other Repco or Supercheap stores might have had them. I'm very surprised Ford have made a part like that obsolete already. Absurd. What next, EF brake pads?! The car cranks longer now before firing on start up, seems to be taking longer to build correct fuel pressure. Wondering what could have changed since I had all the injection system undone? believe it or not but near every thing for e series are no longer available from ford, only a few things are still available... i think 10 years is about limit, even au stuff is starting to become obsolete.. so in the next few years ba stuff will start to go... |
||
| Top | |
||
| EFFUTURA4.05SP |
|
|||
|
225 piece O-ring set from supercheap: $12 . Good investment if you do alot of maintainence and work on your car as second hand O-rings are as good as second hand oil filters.
I even get neibours coming over asking to "borrow" some. 
_________________ 1996 EF Futura factory manual |
|||
| Top | |
|||
| LoganNZ |
|
||
|
EFFUTURA4.05SP wrote: 225 piece O-ring set from supercheap: $12 . Excellent I'll go there on the weekend. Then swap out that used one I had to put in tonight in the carpark at work to make the thing safe enough to run.
_________________ Previous cars: |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 31 guests |
