|
| falcon4litreOHC |
|
|||
|
My power steering pulley has started to make a rattling noise which i suspect the bearing is shot.
Update 20/6/06 I have fixed the problem!!!! It was a worn serpentine belt. Took it too a mechanic I know for a quote on a new pwr steering pump to be fitted. He came out to my car too listen to it and in 10 secs he said that noise is from a worn belt on a big plastic pulley. He sprayed some water on the belt and the rattling noise went away for 10sec at idle. Ye Hah i said to myself i have saved myself some $$$$$$. Anyway got home today after going to FORD SPARE PARTS and replaced the belt($53) plus the top idle pulley($27) on the tensioner arm (did the lower one couple wks ago). Started the old girl up and no more weird sounds. All i can hear now is the injectors pulsing. Cheers......................... Cheers.......... Last edited by falcon4litreOHC on Tue Jun 20, 2006 8:10 pm, edited 1 time in total. |
|||
| Top | |
|||
| smoke_ |
|
|||
|
buy a reco one from fulcrum - $103 - exchange.
i'm buying one tomorrow, couldn't be bothered with the rooting around.
_________________ NEW RIDE - FPV FG F6 6spd Auto. 12.26@114MPH, 1.88 60FT on Cheapy Tyres with 38PSI - Stock except K&N filter! |
|||
| Top | |
|||
| falcon4litreOHC |
|
|||
|
The pulley is only $35 and that's all i want too replace. I just want to remove the belt and then somehow get the pulley off and then wack the new one on.
Gregorys manual says you need a special tool, but i am sure someone on these forums must have worked out a method to get this pulley off... cheers.. |
|||
| Top | |
|||
| Leroy |
|
||
|
im pretty sure its just a normal puller that should do the trick
_________________ Now driving a Hilux |
||
| Top | |
||
| smoke_ |
|
|||
|
ah ok, sorry i thought u wanted a whole new pump.
i haven't tried it, but i would think a standard 3 or 4 legged puller and a bit of care would do the trick.
_________________ NEW RIDE - FPV FG F6 6spd Auto. 12.26@114MPH, 1.88 60FT on Cheapy Tyres with 38PSI - Stock except K&N filter! |
|||
| Top | |
|||
| falcon4litreOHC |
|
|||
|
The tool is shown in a photo in the gregory's manual and looks like a bolt with two different sized hex heads on either end and about 2inches long.
|
|||
| Top | |
|||
| madmax |
|
|||
|
I don't see how replacing the pulley is going to fix a faulty bearing?
_________________
|
|||
| Top | |
|||
| jessev1983 |
|
||
|
just get a reco it comes with the pulley
_________________ 97 EL Fairmont Ghia I6
|
||
| Top | |
||
| msman |
|
||
|
repco sell an aftermarket tool for around $100.
but as said how is replacing a pulley going to fix a buggered bearing? either rebuild the pump yourself, i don't think it needs the pulley to come off as you just dismantle from the rear. or get exchange, new.
_________________ why do u write in here. |
||
| Top | |
||
| falcon4litreOHC |
|
|||
|
msman wrote: repco sell an aftermarket tool for around $100.
but as said how is replacing a pulley going to fix a buggered bearing? either rebuild the pump yourself, i don't think it needs the pulley to come off as you just dismantle from the rear. or get exchange, new. From what i can see, there is a bearing pushed inside the pwr str pulley, much like the idle pulleys found on the tensioner arm. I just thought when you buy a replacement pulley it comes with a new bearing. cheers............... |
|||
| Top | |
|||
| Leroy |
|
||
|
not the case sorry. the pulley is just pressed on to the shaft. no bearings. must have a noisy pump there mate
_________________ Now driving a Hilux |
||
| Top | |
||
| jessev1983 |
|
||
|
there not expensive reco. there only about $120
_________________ 97 EL Fairmont Ghia I6
|
||
| Top | |
||
| stockstandard |
|
|||
|
falcon4litreOHC wrote: msman wrote: repco sell an aftermarket tool for around $100. but as said how is replacing a pulley going to fix a buggered bearing? either rebuild the pump yourself, i don't think it needs the pulley to come off as you just dismantle from the rear. or get exchange, new. From what i can see, there is a bearing pushed inside the pwr str pulley, much like the idle pulleys found on the tensioner arm. I just thought when you buy a replacement pulley it comes with a new bearing. cheers............... If there was a bearing inside the pulley then it would just spin and nothing in the pump would turn.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| GTBob |
|
|||
|
falcon4litreOHC wrote: msman wrote: repco sell an aftermarket tool for around $100. but as said how is replacing a pulley going to fix a buggered bearing? either rebuild the pump yourself, i don't think it needs the pulley to come off as you just dismantle from the rear. or get exchange, new. From what i can see, there is a bearing pushed inside the pwr str pulley, much like the idle pulleys found on the tensioner arm. I just thought when you buy a replacement pulley it comes with a new bearing. cheers............... Buy yourself a manual ( needed for all home mechanics)  
_________________ Rotten Old Revhead!!! XW GTHO + EF ex cop car (exractors 2.5 cat back zorst !6" Simmons K&N +airbox mods Lowered with Bilstein shocks+Whiteline Bars NEXT THING Swap HO for GTP or Ferrari! |
|||
| Top | |
|||
| MARK.TANIA |
|
||
|
just replace the pump .rember this is your steering''and than you now that it is safe a cuppale of 100 bucks for saftey and peace of mind is the way to go''
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 71 guests |
12.06@120MPH
