Fordmods Logo

service 

 

Page 1 of 1 [ 8 posts ] 

 
 Post subject: service
Posted: Sun May 13, 2007 5:11 pm 
Tyre Shredder
Offline
User avatar

Age: 34

Posts: 365

Joined: 14th Feb 2006

Ride: BA falcon

Location: Adelaide
SA, Australia

not sure if this is the right place 2 put this but i thought this was the best place.

my ef gli auto is goin in 4 a service 2moro morning, wat shuld i tell the guy to look at?
the car has been kicking in2 gear lately if i hav been driving it 4 a while and it vibrates heaps wen in drive while holding the brake at the lights.
culd it just only need the trans oil flushed and replaced 2 stop this?

 

_________________

Real Men Smoke Rubber

Top
 Profile  
 
 
Posted: Sun May 13, 2007 5:27 pm 
Getting Side Ways
Offline

Age: 36

Posts: 1538

Joined: 4th May 2006

Gallery: 4 images

Ride: ef fairmont turbo

Power: 213 rwkw

Location: melbourne
VIC, Australia

just do a tranny service by changing the oil, not much else is needed for the tranny.
also do the basics like spark plugs, oil, oil filter, ignition leads and fuel filter if they havent been done in a while, the vibrating while stationary could be cause of heaps of reasons, nothing major even crappy fuel, so run some high octane fuel for a couple of tanks and see if that does the job.

 

_________________

96 EF FAIRMONT
Garrett gt40turbo, iceman plenum, ported head, turbo cam, double valvesprings, 023 fuel pump, 36lb injectors 4' cat, 4' dump, 2.5 exhaust, build bottom end, hypertonic pistons rods & rods, king bearings, j3. c10 3500 stall
232rwkw@4psi

Top
 Profile  
 
 
Posted: Sun May 13, 2007 5:30 pm 
Getting Side Ways
Offline

Posts: 6113

Joined: 8th May 2007

Do the trans filter as well.
Top
 Profile  
 
 
Posted: Sun May 13, 2007 6:49 pm 
Getting Side Ways
Offline
User avatar

Age: 47

Posts: 1669

Joined: 23rd Dec 2004

Gallery: 1 images

Ride: Boosted ED XR6, EBII Mont Wgn

Power: 252 rwkw

Location: Mildura
VIC, Australia

the vibration when in drive at the lights.. will most likely be one of your engine mounts..

 

_________________

Image
[SEXYR-6] ED XR6 T5 Turbo Build
[EBW-347] EB Wagon V8 Stroker Build
FordMods Member #1761

Top
 Profile  
 
 
 Post subject: engine mounts
Posted: Sun May 13, 2007 8:02 pm 
Getting Side Ways
Offline

Age: 35

Posts: 554

Joined: 24th Mar 2007

Gallery: 2 images

Ride: ef 5 speed

Location: melbourne
VIC, Australia

if you auto is kicking in late the oil is to old or there is not enough in it and the vibration most likly will be engine mounts they are a b**ch on this model make shore you get the rubber ones not the oil filled ones they just break other wise and you have the same problem again and just make sure you go toa good workshop and they will only do what is need to be done

 

_________________

i am in need of a new front bar or good condation secondhand for a 95 ef futra,
lsd for a for ef ,modifed au sump to go in and ef , working air con compressor

Top
 Profile  
 
 
Posted: Sun May 13, 2007 9:55 pm 
Tyre Shredder
Offline
User avatar

Age: 34

Posts: 365

Joined: 14th Feb 2006

Ride: BA falcon

Location: Adelaide
SA, Australia

ok thnks, ye my dad will take it to the guy that has been doing all our cars 4 years, his good and is trustworthy.
i wuldnt hav thought the engine mounts wuld be the problem tho. culd the vibration be caused by a timing problem?

 

_________________

Real Men Smoke Rubber

Top
 Profile  
 
 
Posted: Mon May 14, 2007 1:18 pm 
Getting Side Ways
Offline

Age: 36

Posts: 1538

Joined: 4th May 2006

Gallery: 4 images

Ride: ef fairmont turbo

Power: 213 rwkw

Location: melbourne
VIC, Australia

ducati119 wrote:
culd the vibration be caused by a timing problem?



it could be from heaps of diffrent things, to hard to tell. are the revs droping when the car vibrates??? or does it constantly happen while the car is stoped? and does it happen on netruel aswell or just when on drive???

 

_________________

96 EF FAIRMONT
Garrett gt40turbo, iceman plenum, ported head, turbo cam, double valvesprings, 023 fuel pump, 36lb injectors 4' cat, 4' dump, 2.5 exhaust, build bottom end, hypertonic pistons rods & rods, king bearings, j3. c10 3500 stall
232rwkw@4psi

Top
 Profile  
 
 
Posted: Mon May 14, 2007 5:37 pm 
Tyre Shredder
Offline
User avatar

Age: 34

Posts: 365

Joined: 14th Feb 2006

Ride: BA falcon

Location: Adelaide
SA, Australia

the revs sumtimes dropps a little and varies a bit, but it doesnt vibrate in nuetral, but in nuetral the revs occasioinaly dropp slightly 2.

 

_________________

Real Men Smoke Rubber

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 8 posts ] 

Who is online

Users browsing this forum: Google Adsense [Bot] and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Wed Nov 27, 2024 7:29 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names