|
| falcon_3512003 |
|
|||
|
duno geting very limeted on cash now so have to see
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| cjh |
|
|||
|
Yeah, know about that one, $16.25 an hour, yaaahhhh!!!! I,m so glad i've been collecting stuff for years. And can do most of the mods myself.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
yer just trying to deside weather to do the valvs b4 or after i get the head done
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| cjh |
|
|||
|
I've been collecting bits for my engine for the last 5yrs. I still don't have everything yet. Then theres a bit of machining to do too. Mind you though, i have done the whole suspension setup, rebiult g'box, rebiult & change diff ratio, clutch, all the brakes, fuel system, put a new roof on ( the old one had a rust hole in it the size of my hand at the rear corner, and filled the centre console with water when it rained). Had to find another set of wheels for it, all of them (5) were buckled when i got it.
Its been a long road.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
s**t sounds like it how did the rust form in that i havent seen many with bad rust and my mate owns a panal beating shop what e siries is it
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| cjh |
|
|||
|
Its a 4/88 EA 'S' pack sedan. The rear windscreen was never glued in properly, you could push it out in the top corners to a gap of about 1/2".
I bought a brand new roof from ford ( about 4yrs ago) and at the time there were 17 remaining at ford in Melb. I fitted it myself.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
ah ok ea yep cool my x mises has a spak and that had a lot rust to we got rid of it to much to fix & iv just finished grinding 3 of the ex seats and they have come up realy good piting goan so they wernt that bad lets hope the rest come up like these 3
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| cjh |
|
|||
|
Have you got your own valve grinder bench & gear?
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| falcon_3512003 |
|
|||||
|
nar just useing 2 grades of valve grinding past and a dril heres a pik
_________________ now have a series 1 au starting the mods slowly |
|||||
| Top | |
|||||
| cjh |
|
|||
|
Be careful doing that, you may end up with a seat width too wide, or the seats being concave/convexed. They don't seal too well like that under compression.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
yer im keeping my eye on that i know the cleveland heads are bad for it sometimes but dose this look ok to you so far
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| cjh |
|
|||
|
Dunno, you would have to put bearing blue on it to see how wide the seats are gonna be.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
ol get the guy to chek it out tomora when i get it shaved deo ya recon i should get 10thow off it coz no1 has realy sed anything here bout that yet?
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 115 guests |
