|
| falcon_3512003 |
|
|||
|
after geting a new cam today and doing some porting will there be any benafit in geting the head shaved say 10thow to rase comp not sure on these e siries engins any help in deciding this would help
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| fordfreak ef |
|
|||
|
slightly higher compression ratio can be beneficial.. try using premium fuel with that combo though..
|
|||
| Top | |
|||
| cjh |
|
|||
|
How did the porting go? Don't forget to remove the sharp edge around the combustion chamber, helps stop it pinging.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
fordfreak do you recon 10thow will be ok or more or less ? cjh porting is going good just doing some more now will post a pik later to show you
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| cjh |
|
|||
|
Did you get a billet cam or a regrind? How big is the cam?
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
got a regrind a wade 1636 hay how do i get these dam valve stem seals off there on like glue
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| cjh |
|
|||
|
I use a BMW spark lead tool. Its like a pair of pliers with a hole that has teeth, anyway, they are very tough to remove. Use a socket, about 12mm, in 3/8" drive (12 point) to fit new ones.
How much was the cam?
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
cam was 120 change over and ya have to shim it wich ya get from ford 50 buks yer them seals are a s**t but will get em havent let anything beat me yet lol
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| falcon_3512003 |
|
||||||
|
here some piks
_________________ now have a series 1 au starting the mods slowly |
||||||
| Top | |
||||||
| falcon_3512003 |
|
|||
|
i got them dam stem seals off to amazing what a screwdriver and hamer do +u can see were the gasket was leaking in the 4 spots
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| cjh |
|
|||
|
You'll have to put a chemical flush through the system when you get it back together, lookin at the corossion in it. I use Loctite brand, 15 min stuff.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
yer it need a good flush i just been toping the water up wen it was geting low coz of the leak and didnt wory bout the coolent stuff no point on puting it in when it was just leaking out but will be giving it the good stuff onece done it all
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| Seannyb |
|
||
|
Im in much the same kinda pickle.
I have me tickford head that im swapping over for my stock one, im going to get it decked just so its got a nice clean surface to go down on. That and an AU gasket should go a treat.
_________________ Car Killer. |
||
| Top | |
||
| falcon_3512003 |
|
|||
|
whats with the au gasket coz i got all my gaskets yesterday think the brand is vrs
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| cjh |
|
|||
|
The AU headgasket is made of metal shims,(like diesel h'gasket), unlike previous gaskets, that were composition gaskets.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 48 guests |
