|
| bry40l |
|
|||
|
hi just wondering whats involved in fixing a stripped dizzy driveshaft?
thanks
_________________ BF XR6 |
|||
| Top | |
|||
| SWC |
|
||
|
Stripped as in the gear or is there an issue with the Dizzy?
|
||
| Top | |
||
| bry40l |
|
|||
|
Im gonna say the gear as far as I know it was the part in the motor not the dizzy
_________________ BF XR6 |
|||
| Top | |
|||
| chrisxr695 |
|
||
Age: 41 Posts: 16 Joined: 11th Oct 2010 Ride: ef xr6, bf typhoon, mk2 cortina Location: adel |
hay mate. i've had the same prob with my ef xr6 a few times. u might be able to change the cam angle sensor(looks lik a dizzy without the top) and flush the motor. but check the aux shaft to see if thats trashed. if it is u gotta pull all the bolt ons off and the timing cover and chain and change the aux shaft. when u get a new or second hand cam angle sensor check for up and down play cos that the main corse of the prob. if its got to much play it will jam when spinning and strip the gears. i've had this prob a few times and if it just the sensor it a 10min job plus engine flush. if the aux shaft is boned then it's a big job. pays to do ur timing chain at the same time.
hope that helps
_________________ 95 ef xr6 project, 69 mk2 2 door cortina project, 06 bf typhoon, 89 vn ss, 95 vs s pack. time for a new house cos i need more room lol. |
||
| Top | |
||
| bry40l |
|
|||
|
Thanks and I thought it would be an engine out job lol, its an el engine n dizzy im dealing with,
_________________ BF XR6 |
|||
| Top | |
|||
| EA-SPAC-88 |
|
||
|
i recently got my block bored and honed, and we found that the aux shaft was striped so i had to replace it, but in doing that you have to replace the dizzy shaft, or get a new dizzy as the problem will occur again,
|
||
| Top | |
||
| chrisxr695 |
|
||
Age: 41 Posts: 16 Joined: 11th Oct 2010 Ride: ef xr6, bf typhoon, mk2 cortina Location: adel |
u don't gotta pull the motor just pull the thermos and rad out. and thats only to get clearance to get a puller on the crank pully to get it off
_________________ 95 ef xr6 project, 69 mk2 2 door cortina project, 06 bf typhoon, 89 vn ss, 95 vs s pack. time for a new house cos i need more room lol. |
||
| Top | |
||
| bry40l |
|
|||
|
ahk thanks
_________________ BF XR6 |
|||
| Top | |
|||
| chrisxr695 |
|
||
Age: 41 Posts: 16 Joined: 11th Oct 2010 Ride: ef xr6, bf typhoon, mk2 cortina Location: adel |
quick tip get a rare earth magnet and wack it on ur sump on the out side near where the oil pick up is. to grab any lose bits of metel that don't get flushed out. u can do the aux shaft in a day if u are any good with a spanner and hit it hard
_________________ 95 ef xr6 project, 69 mk2 2 door cortina project, 06 bf typhoon, 89 vn ss, 95 vs s pack. time for a new house cos i need more room lol. |
||
| Top | |
||
| bry40l |
|
|||
|
im beginning to think i mite just get another engine or take the engine out of my spare car and drop it in,lol
_________________ BF XR6 |
|||
| Top | |
|||
| bry40l |
|
|||
|
anyone know how much a aux shaft is? i was reading somewhere ford dont have them anymore
_________________ BF XR6 |
|||
| Top | |
|||
| TROYMAN |
|
||
|
no longer available!! you will have to get one out of another engine...
if your engine has alot of kms and is std?, i would just put another engine in.. |
||
| Top | |
||
| bry40l |
|
|||
|
Ahk well I have a spare ef engine but the el hasent clocked 200 thou yet, mite just swap the part
Thanks
_________________ BF XR6 |
|||
| Top | |
|||
| TROYMAN |
|
||
|
i would check the oil when you drain it out to see ho much metal is in it, as any metal shavings have also now been circulated through your oil pump and fine particles will have also been pumped through the rest of the engine.
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Facebook [Bot] and 106 guests |
