|
| davidtg85233 |
|
||
|
Hi guys. My EF Fairmont having some tapper noise when it's getting warm. However, sometimes did a while high rpm for high speed. It doesn't came on stright. What should be happen and how to fix this tapper noise?
Please help a bit.... Thanks |
||
| Top | |
||
| Shortshift |
|
|||
|
The tappets (we usually call them HLAs) gum up over time and don't work properly. To rectify this, try adding some lifter treatment:
http://www.nulon.com.au/products/Lifter ... d_Tune-Up/ If that doesn't fix the noise, then you'll have to replace them with a new set. You'll also need a new set of HLA retainers (if you haven't got extra shims and a reground cam). The old retainers harden & disintergrate over time.
_________________ AU2 XR8 with Raptor VL, ported Yella Terra GT40P heads, Scorpion 1.6 RRs, XE264HR-14 Comp Cam, ceramic coated Hurricane Headers, 60lb injectors, Walbro 255, 200cfi cats, 3" exhaust & Snow Performance water methanol injection |
|||
| Top | |
|||
| dragonsmatt |
|
||
|
I had the same prob a while ago in my EF Falcon, I just went straight to replacing the HLA's its pretty cheap and at least you will know they are new and it will take a long time for that to happen again.
|
||
| Top | |
||
| paul09 |
|
||
|
what happens if you have this problems and don't fix it? Will it break stuff other than tappets themselves?
_________________ 1: Mum's car: ED XR6 wagon.zorst,stereo |
||
| Top | |
||
| frd906n |
|
||
|
yes it will break something, best of changing them, if its noisey while at high rpm ever thought about the oil pressure isnt enough
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| paul09 |
|
||
|
frd906n wrote: yes it will break something, best of changing them, if its noisey while at high rpm ever thought about the oil pressure isnt enough mine doesn't do it at high rpm. just on cold start for about 3-4seconds, oil pressure sits really low then after like 4secs it goes to normal pressure and noise disappears. Just filled car with 20w50 yesterday and it helped a lil bit but noise is still there...
_________________ 1: Mum's car: ED XR6 wagon.zorst,stereo |
||
| Top | |
||
| Troy |
|
||
|
how loud is it? sometimes the tops break off. which means nothing will fix it but replacement.
otherwise you can pull them apart and clean them up |
||
| Top | |
||
| BEAR80 |
|
|||
Age: 44 Posts: 683 Joined: 4th Mar 2010 Ride: BF Fairmont Ghia & TS Magna Location: central coast |
Hey
I put the nulon stuff in my wagon and it's only been driven roughly 50 kays and the HLAS in my car have quietened down a lot and my wagon had sat in a car yard for over 6 months doing nothing unregistered and barely even getting started, so yes this stuff works and it was worth the $11 it cost cheers bear |
|||
| Top | |
|||
| paul09 |
|
||
|
BEAR80 wrote: Hey I put the nulon stuff in my wagon and it's only been driven roughly 50 kays and the HLAS in my car have quietened down a lot and my wagon had sat in a car yard for over 6 months doing nothing unregistered and barely even getting started, so yes this stuff works and it was worth the $11 it cost cheers bear Awesome, thanks for letting us know mate, I'll go pick some up this arvo and try it out 
_________________ 1: Mum's car: ED XR6 wagon.zorst,stereo |
||
| Top | |
||
| BEAR80 |
|
|||
Age: 44 Posts: 683 Joined: 4th Mar 2010 Ride: BF Fairmont Ghia & TS Magna Location: central coast |
paul09 wrote: BEAR80 wrote: Hey I put the nulon stuff in my wagon and it's only been driven roughly 50 kays and the HLAS in my car have quietened down a lot and my wagon had sat in a car yard for over 6 months doing nothing unregistered and barely even getting started, so yes this stuff works and it was worth the $11 it cost cheers bear Awesome, thanks for letting us know mate, I'll go pick some up this arvo and try it out too easy hopefully it works for you cheers bear |
|||
| Top | |
|||
| TIAMO |
|
|||
|
For $6 a piece and 1-2 hours work id replace the hla's. Not hard at all
|
|||
| Top | |
|||
| paul09 |
|
||
|
well i was due for an oil change anyway so did a full flush, new filter, new oil and the nulon lifter stuff.
SO hopefully tomorrow morning on cold start it'll be a bit better
_________________ 1: Mum's car: ED XR6 wagon.zorst,stereo |
||
| Top | |
||
| BEAR80 |
|
|||
Age: 44 Posts: 683 Joined: 4th Mar 2010 Ride: BF Fairmont Ghia & TS Magna Location: central coast |
TIAMO wrote: For $6 a piece and 1-2 hours work id replace the hla's. Not hard at all thats a valid opinion but my HLA'S were only gummed up due to the car being parked up for over 6 months cheers bear Last edited by BEAR80 on Mon May 10, 2010 11:23 am, edited 1 time in total. |
|||
| Top | |
|||
| TIAMO |
|
|||
|
Food for thought i replaced my hla's 6 months ago with ones from Bursons, no o ring on them, a few weeks later the ticking came back. Thought it must be something else so replaced the timing chain tensioner, but still ticking. Opened the rocker cover again only to find 2 already broken after only a few weeks of normal driving. Got replacements with the o ring from Skaf auto parts bankstown for half the price ($6) with the o ring and still perfect.
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 74 guests |
