|
| huggiebear |
|
|||
|
hey all, as sone of you know i recently installed an EL XR6 motor to my fairlane, and while i was at it a new water pump and thermostat... ever since then my thermostat housing keeps springing leaks. we have tried gasket goop aswell as brand new gaskets but nothing seems to work. i bought the thermostat from autobarn and i think it might hold too much pressure behind it because when i ran the car with none i never had a leak. altho i didnt have any hot water for the heater i think thats what im going to have to do. or try my old one
|
|||
| Top | |
|||
| The MaDDeSTMaN |
|
|||
|
Have you tried putting the thermostat in a saucepan of cold water, then boiling the water to see if it opens before the water is full on boiling, and how much it opens in total?
|
|||
| Top | |
|||
| huggiebear |
|
|||
|
its 2 weeks old, i would assume a new thermostat would work...
|
|||
| Top | |
|||
| The MaDDeSTMaN |
|
|||
|
Yeah, you'd hope so, but it wouldn't be the first time something brand new didn't work properly, and it's easy enough and cheap to check.
|
|||
| Top | |
|||
| huggiebear |
|
|||
|
true. ill give it a go tomorrow
|
|||
| Top | |
|||
| TROYMAN |
|
||
|
when you say gasket goop do you meen that brown brush on stuff??
try black gasket silicon or the ultra blue gasket silicon.. |
||
| Top | |
||
| huggiebear |
|
|||
|
we used the blue one. the strong stuff. i cant work it out...
|
|||
| Top | |
|||
| The MaDDeSTMaN |
|
|||
|
Good idea there, ultra blue is good s**t!
|
|||
| Top | |
|||
| ghia97 |
|
||
|
Make sure you give the seat where the thermostat sits in the housing a thorough clean and even a light sand, use genuine thermostat and seal, i put grease around entire seal to make sure it seated and sealed properly, and last but not least dont overtighten screws into housing or you will have constant leaks. I wouldnt use the goop there as if it clumps in one section this alone will cause a leak.
|
||
| Top | |
||
| natho |
|
||
|
i had problems with the thermostat seal leaking on our falcons and found that coating it in petroleum jelly (vaseline) works very well. i'm not sure where I got this idea from but I'm sure it was from a workshop manual from another car.
|
||
| Top | |
||
| huggiebear |
|
|||
|
ghia97 wrote: Make sure you give the seat where the thermostat sits in the housing a thorough clean and even a light sand, use genuine thermostat and seal, i put grease around entire seal to make sure it seated and sealed properly, and last but not least dont overtighten screws into housing or you will have constant leaks. I wouldnt use the goop there as if it clumps in one section this alone will cause a leak.
its not the actual thermostat thats leaking its where the housing meats the block |
|||
| Top | |
|||
| TROYMAN |
|
||
|
have you checked to see if there is any fine cracks?
iv seen a few of them crack from over tightening. |
||
| Top | |
||
| huggiebear |
|
|||
|
na i havnt checked that. tho i will do. cheers
|
|||
| Top | |
|||
| COPEZ |
|
||
|
under the heat of the engines operating tempreture the housing will warp not much but enough you need to lay wet and dry sand paper on a flat surface and rub it slowly back and forth, turn it up and you will see the differance high and low
|
||
| Top | |
||
| huggiebear |
|
|||
|
i think ill just buy a new thermostat housing. they are only like 30 bucks from repco
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 128 guests |
