|
| HSVETAR |
|
|||
|
A mate in his EB ran a pod inside the engine bay and found no performance, yet he cut a 110 mm hole in his guard and ran some 3inch mandrel bend stainless from a pod he mounted in his wheel arch infront of the tyre and it made a heap of difference...!!! Supprisingly it doesnt get as dirty as quick as you would think.
_________________ EL 4.0, XR6 cam, Pacemaker extractors, 2.5" exhaust, 17" Advanti Racing Stalker Rims, Ultra Low King Springs, K&N Pannel filter, NOW MANUAL, 3.45:1 LSD
|
|||
| Top | |
|||
| MoNGooSE |
|
|||
|
HSVETAR wrote: A mate in his EB ran a pod inside the engine bay and found no performance, yet he cut a 110 mm hole in his guard and ran some 3inch mandrel bend stainless from a pod he mounted in his wheel arch infront of the tyre and it made a heap of difference...!!! Supprisingly it doesnt get as dirty as quick as you would think.
Was thinking of doing something similar to that with my new GT bar... Will figure it out when I come to it...
_________________ EF GT6 - 129.4rwkw - Feautured in Street Fords Issue #77 |
|||
| Top | |
|||
| HSVETAR |
|
|||
|
Works a treat mate and gives one hell of an induction noise....
_________________ EL 4.0, XR6 cam, Pacemaker extractors, 2.5" exhaust, 17" Advanti Racing Stalker Rims, Ultra Low King Springs, K&N Pannel filter, NOW MANUAL, 3.45:1 LSD
|
|||
| Top | |
|||
| stomper |
|
|||
|
xhute0 wrote: Is a pod better than a filter? its a bit like asking is the glass half full or half empty..
That all depends if you are a pessimist or an optimist!!!!
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
| Top | |
|||
| huggiebear |
|
|||
|
stomper wrote: xhute0 wrote: Is a pod better than a filter? its a bit like asking is the glass half full or half empty.. That all depends if you are a pessimist or an optimist!!!! i say it both ways.. its half full if your filling the glass, and half empty if your drinking it... makes sense to me |
|||
| Top | |
|||
| MoNGooSE |
|
|||
|
huggie...... you idiot mate
_________________ EF GT6 - 129.4rwkw - Feautured in Street Fords Issue #77 |
|||
| Top | |
|||
| phatal |
|
||
Age: 42 Posts: 517 Joined: 3rd Dec 2004 Ride: SZ Titanium & ZG Fairlane Location: Roxby Downs |
Question.
Do you think that a T series or BA series factory pod filter cold air setup would fit in the E series Bay? Been thinking at looking into the possibilities of doing this.
_________________
|
||
| Top | |
||
| huggiebear |
|
|||
|
only oneway to find out
|
|||
| Top | |
|||
| MoNGooSE |
|
|||
|
Yeh was thinking the same thing... There's a pod filter setup supposedly off of a BA GT on eBay at the moment... It got me thinking... I'm sure it wouldn't be heard to make fit
_________________ EF GT6 - 129.4rwkw - Feautured in Street Fords Issue #77 |
|||
| Top | |
|||
| MoNGooSE |
|
|||
|
Here's the link... It's also got provisions for a shaker
http://cgi.ebay.com.au/Boss-v8-ford-air ... dZViewItem
_________________ EF GT6 - 129.4rwkw - Feautured in Street Fords Issue #77 |
|||
| Top | |
|||
| huggiebear |
|
|||
|
i want a new shaker... i have always wanted to be the first I6 boxcar with a GT shaker... it would look tough on the flat bonnet
|
|||
| Top | |
|||
| les7918 |
|
||
|
actually a external air filter for an eb, eb or ef would be good, i wouldnt mind one for my ef, although im looking at a stage 2 cam, what do you think.
|
||
| Top | |
||
| MoNGooSE |
|
|||
|
Don't know s**t about cams but external air filter sounds good. This for an i6 I'm assuming?
_________________ EF GT6 - 129.4rwkw - Feautured in Street Fords Issue #77 |
|||
| Top | |
|||
| fastleno |
|
|||||
|
here you go huggy a preview
|
|||||
| Top | |
|||||
| huggiebear |
|
|||
|
hahaha i didnt want the XR bulge... just the shaker
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 15 guests |
