|
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
.
Last edited by tickford_6 on Thu Jun 13, 2013 9:40 pm, edited 1 time in total. |
||
| Top | |
||
| Rick_Deckard |
|
|||
|
Will be interesting to see how she runs after all this work.
_________________ E39 523i |
|||
| Top | |
|||
| MYLO_XR6 |
|
||
|
you said the cylinder walls were glazed?!?!?!
that calls for a proper rebuild....bore and honing.
_________________
|
||
| Top | |
||
| Disco Frank |
|
|||
|
MYLO_XR6 wrote: you said the cylinder walls were glazed?!?!?!
that calls for a proper rebuild....bore and honing. depends on the amount of glazing a light hone is all that is needed in some cases to bring the walls back and with new rings will seal nice and tight hope it all goes well for ya man! sounds like fun!
_________________ RIP SCOTT |
|||
| Top | |
|||
| 66 coupe |
|
||
|
Looks like you had a bit better run than my "cheap engine swap" turned out to be
|
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
MYLO_XR6 wrote: you said the cylinder walls were glazed?!?!?!
that calls for a proper rebuild....bore and honing. if the wear is still within tolerence honing is all thats needed. |
||
| Top | |
||
| Kingkezza |
|
|||
|
how many kays the engine has done? well hopefully it'll run nice anyway!
_________________ 5spd Heritage Green EL XR6. Wheels by ROH. Stereo by Clarion. Exhaust by Pacemaker & Lukey. Suspension by Whiteline, Durashock and K-Mac. |
|||
| Top | |
|||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
it had about 220 000km on it befor it came out.
at this point in time. it has turned over about 6 times with the use of a socket and bar. it should go pretty well. with the 4 thou of the head (and the 23 that came off a while back when it blew a gasket) along with an AU head gasket (the AU gaskets have about 4cc less volume then the pre AU gasket and most aftermarket ones) the compression should be getting up close to 10:1 just have to wait untill teusday, it should be all in and running by about 11pm |
||
| Top | |
||
| Slick |
|
|||
|
Is this the kostecki CNC head motor you're rebuilding?
When you're ready, show us some dyno figures. really like to see how much power this heads can do with the right combination.
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| smoke_ |
|
|||
|
sounds like she'll go alright now, any 'go fast' bits going in it?
_________________ NEW RIDE - FPV FG F6 6spd Auto. 12.26@114MPH, 1.88 60FT on Cheapy Tyres with 38PSI - Stock except K&N filter! |
|||
| Top | |
|||
| CordlezToaster |
|
||
|
Quote: AU head gasket and bolts
Are they the steel head gaskets?
_________________ Bacon and eggs for breakfast.
|
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
Slick wrote: Is this the kostecki CNC head motor you're rebuilding?
When you're ready, show us some dyno figures. really like to see how much power this heads can do with the right combination. no this was just a quick freshen up of the stock engine as oil consumption was getting a bit out of hand. the only thing not stock in this is an RPD stg1 cam. the other engine is still comming along nicely though. |
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
CordlezToaster wrote: Quote: AU head gasket and bolts Are they the steel head gaskets? thats the one. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 128 guests |
12.06@120MPH