|
| TROYMAN |
|
|||||||
|
well here is the car now lol
i decided not to f**k around anymore. im half way there. the heater box is out and ive fitted the ef heater core and evaporator core. but ive run out of light so ill get back into it in the morning..
Last edited by TROYMAN on Tue May 20, 2008 9:08 pm, edited 1 time in total. |
|||||||
| Top | |
|||||||
| huggiebear |
|
|||
|
crazy stuff... i need to pull mine apart its making funny noises
|
|||
| Top | |
|||
| BenJ |
|
||
|
Gold!!!!! "Got the Mrs putting it back together" LOL
Good job mate, you can do mine next, will be around in the morning. So, how did you get the heater hoses off? BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| TROYMAN |
|
||
|
BenJ wrote: Gold!!!!! "Got the Mrs putting it back together" LOL
Good job mate, you can do mine next, will be around in the morning. So, how did you get the heater hoses off? BenJ ahh special trick  ..
na i took the hoses of when i did the bbm conversion because the heater core was leaking.. tomorrow i still got to put the heater box back in(its a pain to get to those little nuts behind the engine  ),re solder a few wires i cut
and the plastic airhose manifold on the heater box broke so i hope the one on the ef is ok?. and the fun part of getting the heater hoses back on lol... i should have the car back on the road tomorrow arvo or thursday?? then i need another ef tx valve and high/low pressure switch, another aircon re-gas and fingers crossed it wont give me anymore trouble..
oh and the mrs will be happy to have a heater again... |
||
| Top | |
||
| Paulmac |
|
||
|
Sounds like a balanced partnership Troy, the heater to warm the missus up and the aircon to cool you down! LOL
I'm sure that between Ben and yourself, finding a Tx valve and switch won't be too difficult...or costly. LOL He was playing around with EF bits to-day, just follow his fingerprints... Mac
_________________ What goes around, comes around. |
||
| Top | |
||
| huggiebear |
|
|||
|
so whens the dual climate control coming? lol kia carnivals have these stock lol. well its like a 3way one, rear has its own controls and the drivers and passengers are different to each other. would love to have something like this fitted to mine, hot as hell for me warm for the other half
|
|||
| Top | |
|||
| TROYMAN |
|
||
|
woo hooo
its all back together again! the dash is back in and the heater now works great. i had to buy a new heater tap and hoses. tomorrow im off to get a new tx valve,hi/low pressure switch and o rings then re-gas the aircon.. again!! |
||
| Top | |
||
| Paulmac |
|
||
|
That's good news.
Will you be mingling with us on Friday night or will you just sit in the car with the engine and heater on grinning like a Cheshire cat? LOL Cheers, Mac
_________________ What goes around, comes around. |
||
| Top | |
||
| TROYMAN |
|
||
|
yes we will be there on friday but i know we will be warm driving there and back |
||
| Top | |
||
| frankieh |
|
|||
|
that sux.... I don't wanna have to pull my dash out again.. must be a way to adapt the two together even if I have to braze an adaptor onto it.
|
|||
| Top | |
|||
| BenJ |
|
||
|
Sigh, so this looks like something I will be doing soon Sigh
So how did you go getting the heater hoses on? And good job mate. BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| frankieh |
|
|||
|
I want to know what the TX valve does and in what way the EA one differs from the EF/EL one..
I hate pulling dashes out... 
|
|||
| Top | |
|||
| TROYMAN |
|
||
|
frankieh wrote: that sux.... I don't wanna have to pull my dash out again.. must be a way to adapt the two together even if I have to braze an adaptor onto it.
i would say if you dont want to pull your dash out it would be easier to get custom lines made up! i tried to use a mix of factory parts and it did work! but i could not get the ef tx valve to seal properly on the ea evaporator.. so i took the step and pulled the dash out because the heater core was stuffed aswell.. otherwise i should have just got the custom lines made up... and i wouldnt try brazing the pipes on the evaporator as the heat might cause the brass or lead on the core to melt and then you will need to pull the dash out to change that... |
||
| Top | |
||
| TROYMAN |
|
||
|
BenJ wrote: Sigh, so this looks like something I will be doing soon Sigh
So how did you go getting the heater hoses on? And good job mate. BenJ thanks ben i got the heater hoses on ok.. i have scratches all over my hands and arms from forcing my arms between the bbm manifold and body lol.. i found it easier to fit the heater hoses by removing the air intake,aircon lines.and washer bottle. ben i would recommend fixing your heater problem before fixing the aircon. that way you can remove your aircon lines to get to the heater hoses? that way you dont have to lay under the car to get the hoses off... i used ea heater hoses as my engine still has the ea engine pipe. the funny part is it only took 2 1/2 hours to pull everything out including the heater box.. and it then took 7 hours to put everything back together including the heater hoses,re-solder some of the extra wires added from the bbm conversion that i had to cut
|
||
| Top | |
||
| TROYMAN |
|
||
|
ok
its all fixed and finished.
its now been fitted with a new tx valve ect.. i got it re-gassed today and its all working a treat.. the heater is hot as hell and the aircon is as cold as ice.. 
as long as the aircon dont leak its something that i dont want to do again!
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 57 guests |
