|
| Sommers NL |
|
|||
|
Hi all ..
Im replaced the head with a EL 95DT tickford head on my NL instead of the AU3 head that was on it ... Now, is it true you are only meant to run water for the first few 1000kms and then put the coolant in? or can you put coolant in straight away ... Please let me know!!!!! Thanks heaps guys! you all rock!! Luv, Laticia.
_________________ BANNED!!!! |
|||
| Top | |
|||
| PIMP_LTD |
|
||
|
I've never heard that in my life. The only reason i'd ever adhere to that is to make sure you have no leaks equaling a waste of coolant once you fix said leak.
When doing work to the cooling system, i usually run for a day orso with water for the above reason, once i'm happy there is no leaks, in goes the coolant. Andrew
_________________ Commodore australia's favorite car??? What a load of s**t |
||
| Top | |
||
| Sommers NL |
|
|||
|
WOW quick response, so I can fill it up with water, take it around the block, and then put the coolant in? .... Cos im coming down to Brisbane next weekend, to meet up with a few people from here .. anyone else wanna meet up? hehe .
Laticia.
_________________ BANNED!!!! |
|||
| Top | |
|||
| PIMP_LTD |
|
||
|
I'd make sure when you drive it with test water, do it more than just around the block, give the engine enough time to completly heat up. You want it to get to its proper operating temperature, because if there is a problem, it may only be when its fully warm that the gap will open and leak, so you may miss it.
Have a good look along the block/head under the manifolds, and look at all hoses. As long as the block and head surfaces were flat, and work was done good, it should be fine, but a test is always a safe option on such work.
_________________ Commodore australia's favorite car??? What a load of s**t |
||
| Top | |
||
| nannas_ed |
|
|||
|
i always got told to run straight water for a week or so. retension the head bolts and flush and fill with coolent. gives the head gasket time to settle or something like that
_________________
|
|||
| Top | |
|||
| efgreenweapon |
|
||
|
do it a work all the time start car with water drive around the block a few times and check for any leaks presure test if you have a tester and then add coolant and you dont have to retesion head bolts
_________________ now with a nf fairlane with au series 2 motor let the mods comence |
||
| Top | |
||
| BenJ |
|
||
|
In fact DON'T RETENSION THE HEAD BOLTS!!!!! They are designed to be tensioned once.
BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| naughtyfalcon |
|
|||
|
same here when i did the head gasket a year ago,,water for the first week then drain a bit of water and add coolant.
_________________
|
|||
| Top | |
|||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
the 'water only' rule is if you use gasket adhesive and dont want chemicals from the coolant stopping it cure properly
if you use an AU metal gasket you dont need any adhesive, therefore can stick coolant straight in |
||
| Top | |
||
| green car |
|
||
|
Ford told me to use hylomar spray and to run water for a week with my au gasket and ive had no probs.
_________________ 165 Killer Wasps all packaged in a green kmart car, almost an explorer in a way... |
||
| Top | |
||
| Tocchi |
|
|||
|
yeh i ran coolant straight away with AU gasket, it leaked a little bit
head came off again, checked out head, used water, no leaks, swapped it to coolant a week later no issues since |
|||
| Top | |
|||
| macxr8 |
|
||
Age: 55 Posts: 451 Joined: 3rd Jan 2005 Ride: AU XR6 with BF Turbo engine Location: Sydney |
There are chemicals in the head gasket that react to the Ethylene glycol found in a lot of coolants.
From the ACL 05 gasket book Quote: Monotorque gaskets are silicone coated and NO additional sealants should be used. When installation is complete the engine should be filled with water, brought up to normal operating temperature, allowed to cool and then drained. Coolant in accordance with the manufacturer’s specifications is to be mixed with water and then the engine refilled. Another problem with Ethylene Glycol is that it can track along the fibres in a gasket material which can cause leakage problems with gaskets. Thus the reasoning behind allowing an engine to reach operating temp before you add coolant. The heat will set the chemicals in the head gasket off and help with sealing. i have seen a brand new head gasket start to leak as the coolant tracked to the outside.
_________________ RIP |
||
| Top | |
||
| AU2SR |
|
|||
|
green car wrote: Ford told me to use hylomar spray and to run water for a week with my au gasket and ive had no probs.
The head gaskets are coated in a viton rubber and NO sealant is to be used as it acts as a catalist to the coating
_________________ Technical Advisor AA GASKETS |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: CrownFord, Google Adsense [Bot] and 47 guests |
1x confused Falcon..EL Falcon with full AU running gear...VCT, 5 speed, IRS, AUII front suspension, brakes, and steering RIP