|
| Saiken |
|
||
|
Hey,
My drive belt keeps pop'ing off..... i think its cause the big pulley on the crankshaft doesnt line up with the tensioner.... but not sure... i have a picture here: http://www.liquid-pixel.org/Images/DSCN0117%5B1%5D.jpg if you could have a look and tell me what you think is wrong... and post up a pic of yours so i can see if mine is alright.... i have an EF2 Fairmont if that helps (1996) Thanks in advance
_________________ Cobra Motorsports |
||
| Top | |
||
| stockstandard |
|
|||
|
Either the out ring of the balancer is slipping off (likely) or the balancer itself is coming loose (unlikely).
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| The Dog |
|
|||
|
Just from the pic: Is the idler bracket tight on the timing cover? Also what are the bearings like on the idler?
_________________ You'll ride a black tornado across the western sky
|
|||
| Top | |
|||
| Saiken |
|
||
|
yeah, the idler bracket is tight, and the bearings are fine.....
how would i slip the out ring back on the balancer...... or does it need replacing?
_________________ Cobra Motorsports |
||
| Top | |
||
| The Dog |
|
|||
|
That was gunna be my next question
 If the outer ring has slipped on the balancer its rooted. Time to whip it off and get a new one.
_________________ You'll ride a black tornado across the western sky
|
|||
| Top | |
|||
| Saiken |
|
||
|
crap.... how much would i be looking at aprox?
_________________ Cobra Motorsports |
||
| Top | |
||
| stockstandard |
|
|||
|
Yep, the outer ring slipping is pretty common as they get old. Nothing you can do but head down to your local auto store and swap it for a new one.
edit - you can usually see it. Leave the belt off, start it up and have a quick look (dont run the engine for long though). It will probably wobble all over the place.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| stockstandard |
|
|||
|
Saiken wrote: crap.... how much would i be looking at aprox?
~$100'ish you will also need a balancer puller if you havent got one.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| Saiken |
|
||
|
kk thanks
_________________ Cobra Motorsports |
||
| Top | |
||
| Saiken |
|
||
|
got a mate to take some photo's of his engine bay and yeah...... thats the problem... and you can see where it has slipped
_________________ Cobra Motorsports |
||
| Top | |
||
| efgiar |
|
||
|
you can see it in the pic, look were the timing notch is on the motor, sitting HEAPS over the harmonic balancer.
|
||
| Top | |
||
| cjh |
|
|||
|
The balancers shat themselves because the oil would seep up the crank woodraft key slot and sweat out to bugger up the rubber and then the outer ring lets go. So make sure you apply sealant to the key slot on the new balancer.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| Saiken |
|
||
|
lol, shut up efgiar... if you had of been on msn i would have just sent you the pic... but noo... you had to be doing other things =P.
i got anton to take a photo of his and realised the problem aswell.....
_________________ Cobra Motorsports |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 60 guests |
