|
| Campbell18 |
|
|||
|
just got off the phone to the mechanic who said he installed the wade 1636 in the car, but its idling rough and tries to stall when driving
being a mild cam shouldnt it work ok with the computer??
_________________ ED 4.0L auto... pacemaker PH4480, Aus Pac Catback exhaust, wade 1636 with j3 tune =130rwkw |
|||
| Top | |
|||
| nalane |
|
|||
|
1636 is as high as they recomend you go without other engine mods. I had one in my fairlane and it ran fine. Check with your mechanic and make sure he used double shims in the lash adjusters.
|
|||
| Top | |
|||
| 66 coupe |
|
||
|
+1 on the shims
also get your mech to clean out the throttle body, and set the base idle with the ISC disconnected. Also bump up the base timing to 15 degrees, from the usual 10. |
||
| Top | |
||
| nalane |
|
|||
|
yep play with the timing and back it off a touch when it starts to ping. Clean the ISC while doing the throttle body.
|
|||
| Top | |
|||
| Campbell18 |
|
|||
|
he confirmed that it has definitely been double shimmed, i gave wade cams a call, and he said that the battery has to be disconnected for at least half an hour before the computer can re learn itself.The mechanic was going to leave it for a while and then get back to me.
_________________ ED 4.0L auto... pacemaker PH4480, Aus Pac Catback exhaust, wade 1636 with j3 tune =130rwkw |
|||
| Top | |
|||
| nalane |
|
|||
|
Yes the ecu will have to get all the air/fuel peramaters and recalculate everything. Just drive it for a couple of days and take it from there. Sorry I thought you had the car back from the mechanic.
|
|||
| Top | |
|||
| krisisdog |
|
|||
|
Any cam change will generally have the car coughing and spluttering for a while, but you definitely need to reset the ECU. My 1673 would barely run right after it was installed.
|
|||
| Top | |
|||
| GeZza200 |
|
||
|
dont worry about it, mine was pretty rough when i first got that cam in. Mine would stall at lights and if i turned an was in reverse it would stall, so i just adjusted the idle so it would rev at around 850-900rpm.
_________________ EL Futura: CVE head, Wolf V500, ICE Ignition and Coil, 36lb injectors, Walbro 255lb, Paci comps, 3" exhaust, T5, Harrop Truetrac with 3.9s. Now with 198.9rwkw, (~185rwkw and 13.80 @99.1mph) with more power to come |
||
| Top | |
||
| MMD |
|
||
|
When i installed my 1636, it idle'd a little rough (wouldn't say it was a concern) but stalled every time i would put it in gear, and try to drive with no accelerator.
i let it idle for about half an hour, then tried to reverse out of the drive way - about 3 restarts i got to the road, took about 100Km of driving for it to completely stop stalling. |
||
| Top | |
||
| EDXR6-Poly |
|
|||
|
Take it for a good drive and let it run in (about 200ks will do it or drive around town and highway for about an hour or so varying the rev range
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| 66 coupe |
|
||
|
set your base idle correctly and it wont stall at all!
|
||
| Top | |
||
| arm79 |
|
|||
|
Did he bleed the lifters before putting them back in?
If they weren't, they may be holding the valves open slightly, causing the idle stalling. Would also cause the thing to run a bit rich too. And when you say double shim, we hope we are all talking the same thing. |
|||
| Top | |
|||
| Campbell18 |
|
|||
|
thanks for the help guys, took the car for a decent drive earlier today, runs alot smoother once it has warmed up. I upped the base idle slightly to stop it from stalling at the lights, its still running very rich though
looks like j3 chip is the next step?
_________________ ED 4.0L auto... pacemaker PH4480, Aus Pac Catback exhaust, wade 1636 with j3 tune =130rwkw |
|||
| Top | |
|||
| Campbell18 |
|
|||
|
its been almost a week and the car is still fairly rough and fuel consumption isnt to great, surely this isnt normal for such a mild cam??
_________________ ED 4.0L auto... pacemaker PH4480, Aus Pac Catback exhaust, wade 1636 with j3 tune =130rwkw |
|||
| Top | |
|||
| GeZza200 |
|
||
|
Campbell18 wrote: its been almost a week and the car is still fairly rough and fuel consumption isnt to great, surely this isnt normal for such a mild cam?? You will need a J3 chip if you want to run proply and have good economy
_________________ EL Futura: CVE head, Wolf V500, ICE Ignition and Coil, 36lb injectors, Walbro 255lb, Paci comps, 3" exhaust, T5, Harrop Truetrac with 3.9s. Now with 198.9rwkw, (~185rwkw and 13.80 @99.1mph) with more power to come |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 81 guests |
