|
| Wade Cams |
|
|||
Age: 71 Posts: 565 Joined: 8th Nov 2004 Ride: 2011 Kia Optima Platinum Location: Melbourne |
Here are some remarks that have been passed on by a member who has replaced his Wade 1636 cam with the 1636C977B profile.
"Being a manual EA and running an EL ecu, it idles spot on, no surging etc, however in an auto it might have slightly too little vacuum at idle, causing it to hunt a little. Drivablility, this new grind has noticably more torque in the midrange, from about 2200 to 3000, and has a nice pull @ WOT from 3000 to around 4800. The 1636 seemed to run out of puff a bit earlier than the new grind. With standard springs etc, so far its been fine up to 5250rpm. Overall it's a good cam for a manual, works well with lots of revs, however it might be less suited to an auto unless there's a decent diff ratio fitted and / or a hi-stall. It seems to fill the cylinders a slight bit more, because with the new cam, mixtures went slightly leaner at higher rpms than they were with the 1636, meaning slightly more air is in the mix." Cheers Chris WADE CAMS |
|||
| Top | |
|||
| Grechie |
|
||
|
Tommorow ill be dyno'ing the car with the 1636C977B , so ill have a rwkw figure to release.
this cam is noticeably quicker after 140km/h 
_________________ Ford Falcon EA Naturally Aspirated 4.0L i6 |
||
| Top | |
||
| Wade Cams |
|
|||
Age: 71 Posts: 565 Joined: 8th Nov 2004 Ride: 2011 Kia Optima Platinum Location: Melbourne |
Grechie wrote: Tommorow ill be dyno'ing the car with the 1636C977B , so ill have a rwkw figure to release.
this cam is noticeably quicker after 140km/h You're just a very naughty boy! 140km/h. |
|||
| Top | |
|||
| twr7cx |
|
|||
|
Hmmmmmmm... You've got me keen now.
|
|||
| Top | |
|||
| Kenwood Maverick |
|
|||
|
Im keen too. trying to source a good power giving cam for the monster
|
|||
| Top | |
|||
| trebba |
|
||
|
damn sounds like the perfect cam only my ed xr6 is auto
_________________ -----FG MK2 XR6 UTE----- |
||
| Top | |
||
| trebba |
|
||
|
would i benifit from this cam with 3.45 lsd and a hi stall converter ????
_________________ -----FG MK2 XR6 UTE----- |
||
| Top | |
||
| xavier |
|
||
|
any more feedback on this cam from someone who has installed it?
_________________ only 2 things should come in a 2 litre, milk and juice
|
||
| Top | |
||
| Damo |
|
|||
|
yeah grechie lost over half a second over the 1/4 with this cam over a 1636. Apparently that was due to leaning out up top and s**t tyres. I'd like to see him back up his 14.4 with this cam.
|
|||
| Top | |
|||
| Bug |
|
|||
|
Anyone able to compare either 1636 grind to the 1604?, or the 1004 for that matter.
_________________ EL XR6 5spd |
|||
| Top | |
|||
| phongus |
|
|||
|
is this cam a regrind? if so does I am guessing you need shims and stuff?
phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Bug |
|
|||
|
Its just a profile, so it could either be reground or done on a billet cam...
_________________ EL XR6 5spd |
|||
| Top | |
|||
| Damo |
|
|||
|
yeah it's a regrind.
|
|||
| Top | |
|||
| kizzer |
|
|||
|
Damo wrote: yeah grechie lost over half a second over the 1/4 with this cam over a 1636. Apparently that was due to leaning out up top and s**t tyres. I'd like to see him back up his 14.4 with this cam.
is this tru? is there anymore info/comments about it. cause i was looking at this cam for my next upgrade from 1604.
_________________ 1995 EF Fairmont with all the Gear. |
|||
| Top | |
|||
| Damo |
|
|||
|
yeah it is true, ran a 14.4 @96mph with a 1636 cam, ran a 15.2 with the 1636c977b not sure what MPH, but as I said s**t tyres and leaning out, not sure why he bothered running it.
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 46 guests |
