|
| voxace |
|
|||
|
Hey,
Is it possible to weld a plate or something between the two bits of metal on an engine mount to make it stronger? I don't want it to ever break again when I replace it. Cheers. |
|||
| Top | |
|||
| Leroy |
|
||
|
if i am reading correctly the two plates you are talking about are seperated by a block of rubber. this is what helps stop the vibrations. if you weld a plate to it you might as well just bolt your engine straight to the chassis. probably get a whole lot more vibrations
then again i could be dribbling s**t
_________________ Now driving a Hilux |
||
| Top | |
||
| voxace |
|
|||
|
Yeah I don't care lol
|
|||
| Top | |
|||
| MARK.TANIA |
|
||
|
yes you can but the rubber is to stop virabraion and it is elegal
|
||
| Top | |
||
| madmax |
|
|||
|
The vibrations will more than likely break the welds anyway
_________________
|
|||
| Top | |
|||
| Bsjenko |
|
|||
|
mate i can weld it together for u, but i wouldnt recommend it. thats is danger territory
_________________ The Lane Lives.... Finally!!!! |
|||
| Top | |
|||
| Bsjenko |
|
|||
|
madmax wrote: The vibrations will more than likely break the welds anyway
depends how big the welds are, andhow deep they penetrate
_________________ The Lane Lives.... Finally!!!! |
|||
| Top | |
|||
| voxace |
|
|||
|
Well it's a urethane mount, and I could't feel any vibrations at all. But it died in less than a week!
Anything else than can be done? I could have sworn I heard of people welding them up??? |
|||
| Top | |
|||
| MARK.TANIA |
|
||
|
you can also get some chain and weld the links together .and bold it to each end this will help as i did this to my old v8 as it always broke mounts
|
||
| Top | |
||
| voxace |
|
|||
|
What did it feel like??
|
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
arh they aftermarket ones if they are they are prone to breaking buy gen ford ones
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| madeaspack |
|
||
|
those mounts are s**t,i was breaking 2 a week,then they broke and i only had some old rubber ford ones...havent broken since
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| fordzatmyplace |
|
||
|
arn't late model EL (1998) ones meant to be the best?
_________________ ^^^ What He Said
|
||
| Top | |
||
| Slick |
|
|||
|
why don't you order yourself a set of Prothane Engine Mounts inserts.
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| hans hartman |
|
||
|
hi,read your mods,your getting a big motor twist ( torque twist) when you rev. motor out. either idle is too low -will shake engine bay,or using rubbish mounts- replace both sides with fraud ones, a torque chain has to be mounted very solid -it will rip the inner guard. i have seen limiter steel straps on mounts to hold when torn,you can weld a link using chain,loose about 1mm on both sides and both mounts.may reduce vibration, but will transmitt in to subframe. trial and error, if you chain it 75-100mm slack,i had a 6cyl. move 100-170mm on top,with almost 2mm on bottom mounts,twisting on rubbers.are the au mounts heavier?
 good luck
_________________ R.I.P HANS HARTMAN |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Facebook [Bot] and 101 guests |
