|
| efbignik |
|
|||
|
ok i'm thinking of pulling my head off for a bit of
porting and polishing and just wanting to know what head gasket i should use when i put it all back together ????????????? any1 using jmm (Multi-Layer Steel-Head Gasket) are thay any good any help would be gr8
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| Krytox |
|
|||
|
yeh I am,
Use a AU shim head gasket, In fact If you go to ford and ask for a E series gasket... you'll get a AU one
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| twr7cx |
|
|||
|
genuine Ford AU one. Not an aftermarket ones, as aftermarket companies such as ACL don't make metal ones for the AU and that.
|
|||
| Top | |
|||
| efbignik |
|
|||
|
will a au one fit an ef
what makes the au ones better
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| stockstandard |
|
|||
|
Yep it will fit - The JMM one is an AU gasket
AU ones as thinner (good for a bit of extra compression) and stronger.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| efbignik |
|
|||
|
sweet thanks
stockstandard and twr7cx
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| twr7cx |
|
|||
|
Au one is metal compared the the normal ones or previously used ones which are normal gasket material (a fibre paper type stuff). the metal ones last longer and seem to have been the solution to the headgasket failure problem that was common on early 4.0L SOHC I6's.
|
|||
| Top | |
|||
| jaym |
|
|||
|
Does the AU one fit 3.9??
|
|||
| Top | |
|||
| jet ute |
|
||
|
jaym wrote: Does the AU one fit 3.9?? no
_________________ Super Pursuit |
||
| Top | |
||
| jet ute |
|
||
|
twr7cx wrote: Au one is metal compared the the normal ones or previously used ones which are normal gasket material (a fibre paper type stuff). the metal ones last longer and seem to have been the solution to the headgasket failure problem that was common on early 4.0L SOHC I6's. I have a set of au stocks if u want them tyres arnt bad
_________________ Super Pursuit |
||
| Top | |
||
| fordzatmyplace |
|
||
|
jet ute wrote: jaym wrote: Does the AU one fit 3.9?? noare you sure about that?? i have been told otherwise...
_________________ ^^^ What He Said
|
||
| Top | |
||
| Krytox |
|
|||
|
jet ute wrote: twr7cx wrote: Au one is metal compared the the normal ones or previously used ones which are normal gasket material (a fibre paper type stuff). the metal ones last longer and seem to have been the solution to the headgasket failure problem that was common on early 4.0L SOHC I6's. I have a set of au stocks if u want them tyres arnt badWTF??? and Yes, I'm lead to believe the AU gasket fits fine on the 3.9 but you'll need to use AU bolts and torque sequence
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| stockstandard |
|
|||
|
yes you can use Au gaskets on 3.9's
And yes, always use the torque sequence for the type of gasket your using (not the engine).
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| HaZZa |
|
|||
|
i went for a acl race series gasket kit and that looks like its twin metal
|
|||
| Top | |
|||
| stockstandard |
|
|||
|
HaZZa wrote: i went for a acl race series gasket kit and that looks like its twin metal
ACL race = graphite
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Facebook [Bot] and 124 guests |
