|
| racer |
|
||
|
Just wandering what ignition timing are you running on your engine with a performance cam.
I am running 2 degrees advanced extra in other words 12 degrees base timing. I just feel it needs more ignition timing for my engine. I just like to hear what you guys are running before i start to experiment on my engine. I am running premium 98 octane fuel all the time.
_________________ FORD EL 4.0L. Crow cam, T.I Performance J3 Chip, Vernier cam gear, SPR ported head, 68mm TB, AU head gasket + ARP studs, AU injectors, Pacey 4480, High flow cat, Shift kit, Stallie, 3:73 TrueTrac. |
||
| Top | |
||
| ea_falcon |
|
||
|
i dont have an after market cam but im running about 13 to 14 degrees and it does not ping at all with premium and i have a manual. it goes a s**t loads better as well, compared to having it at 10 degrees or retarded i think with a lumpy can high octane and advanced timing will get the most out of it
_________________ 02 series 3 AU marline ute 5speed 347 stroker |
||
| Top | |
||
| 66 coupe |
|
||
|
running 18 base 31 total at wot, on an AUi6 with an unknown cam, megasquirt ecu. no pinigng etc on 95 fuel
Its quite safe to run around 15 base with good fuel on a stock ecu. |
||
| Top | |
||
| GT-01 |
|
|||
|
how do u advance your timing to a set degrees???? any help would b great
|
|||
| Top | |
|||
| EL__Fairmont |
|
|||
|
GT-01 wrote: how do u advance your timing to a set degrees???? any help would b great
Put the ecu in base ign timing mode first. rotate dizzy anti-clockwise. 1.5mm on the crank pulley is about 1 degree. timing light is required................
_________________ 97 EL Fairmont 4l OHC .Silver. |
|||
| Top | |
|||
| cjh |
|
|||
|
I'm running a stock cam, and a piggy back ECU, but have the base timing at 16dgs and is advanced by about 4 dgs ( thats whats added to the original ignition curve) up to about 3500rpm then 2dgs up to 4500rpm.
It doesn't ping, using ULP, and the donk ain't real good....LOL.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| TROYMAN |
|
||
|
im using a el ecu at about 13-14 deg btdc
|
||
| Top | |
||
| Masier |
|
||
|
66 coupe wrote: running 18 base 31 total at wot, on an AUi6 with an unknown cam, megasquirt ecu. no pinigng etc on 95 fuel
Its quite safe to run around 15 base with good fuel on a stock ecu. This is what I got the ute to run best with gas. It goes like a cut snake. |
||
| Top | |
||
| gogetta |
|
|||
|
cjh wrote: I'm running a stock cam, and a piggy back ECU, but have the base timing at 16dgs and is advanced by about 4 dgs ( thats whats added to the original ignition curve) up to about 3500rpm then 2dgs up to 4500rpm.
It doesn't ping, using ULP, and the donk ain't real good....LOL. just curious as to what piggyback you are running?
_________________ |
|||
| Top | |
|||
| racer |
|
||
|
Thank you very much guy's i appreciate & value all your inputs. I was thinking about 15-16 deg. base timing due to the fact i have the std. (f/mont ghia) ecu.
_________________ FORD EL 4.0L. Crow cam, T.I Performance J3 Chip, Vernier cam gear, SPR ported head, 68mm TB, AU head gasket + ARP studs, AU injectors, Pacey 4480, High flow cat, Shift kit, Stallie, 3:73 TrueTrac. |
||
| Top | |
||
| cjh |
|
|||
|
gogetta wrote: cjh wrote: I'm running a stock cam, and a piggy back ECU, but have the base timing at 16dgs and is advanced by about 4 dgs ( thats whats added to the original ignition curve) up to about 3500rpm then 2dgs up to 4500rpm. It doesn't ping, using ULP, and the donk ain't real good....LOL. just curious as to what piggyback you are running? A Moristech unit. You can change the ignition map & fuel maps separately.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| racer |
|
||
|
RESULTS.
I have the timing set at 18-20 degrees in link mode. And approx. 30-32 degrees at total. NO PINGING. My car excelerates alot faster. It hunts at idle in park or nutral for a bit & then settles but no hunting in drive. I can live with that. I am very happy with the results, TRY IT.
_________________ FORD EL 4.0L. Crow cam, T.I Performance J3 Chip, Vernier cam gear, SPR ported head, 68mm TB, AU head gasket + ARP studs, AU injectors, Pacey 4480, High flow cat, Shift kit, Stallie, 3:73 TrueTrac. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google [Bot], Google Adsense [Bot] and 65 guests |
