|
| eattsie9 |
|
|||
|
just wondering if putting a quality Exhaust system including extractors high flow cat and 2 1/2 zorst gives a good tone?
ive noticed some 6's with performane exhausts get a real horrible whining noise so thought id ask around before i get it done
_________________ Ba Xr6 Boat |
|||
| Top | |
|||
| bry40l |
|
|||
|
It all depends on the mufflers used and how many mufflers/resonators are on it, I have a ef 6cyl with a 2.5inch exhaust and 1 muffler, its got a,terrible drone at low rpm under load, but if I put the foot down it sounds good, imconsidering putting a hot dog resonator on mine to take some of the drone out
_________________ BF XR6 |
|||
| Top | |
|||
| eattsie9 |
|
|||
|
ahk thanks will have to do some research into what sounds good ... on my XF ive got extractors and straight through 2.5 inch with 1 muffler and it sounds amazing so ye
_________________ Ba Xr6 Boat |
|||
| Top | |
|||
| TheKrazeD |
|
||
|
Extractors, High-Flow Cat with twin 2.5inch tips. Sounds f**k amazing. It's not tinny? at all, but more of a rumble. I've had retards try to tell me I drive a V8 all because of the sound....
_________________ VIXEN FG XT Previous best - 14.431 @ 99.69mph with minor mods |
||
| Top | |
||
| eattsie9 |
|
|||
|
TheKrazeD wrote: Extractors, High-Flow Cat with twin 2.5inch tips. Sounds f**k amazing. It's not tinny? at all, but more of a rumble. I've had retards try to tell me I drive a V8 all because of the sound.... haha ye i had the same thing with my old car  thnx for the help
_________________ Ba Xr6 Boat |
|||
| Top | |
|||
| brad17djr |
|
|||
|
depends on the extractors and mufflers and even the tip you use, the extractors make the biggest differnce in sound my mate has a bf with hurricane extractors and it sounds deep where as my fg has pace maker tri Y's and it sounds sort of like a lamboghini when your up it. When i put my exhaust on i was chassing power not sound and i got both
 i have pacemaker 4495's a high flow 3 inch cat then 3'' into 1 offset magnaflow muffler then 3'' into a fg GT rear system.
_________________ 2 FOR TURNING & 2 FOR BURNING |
|||
| Top | |
|||
| eattsie9 |
|
|||
|
brad17djr wrote: depends on the extractors and mufflers and even the tip you use, the extractors make the biggest differnce in sound my mate has a bf with hurricane extractors and it sounds deep where as my fg has pace maker tri Y's and it sounds sort of like a lamboghini when your up it. When i put my exhaust on i was chassing power not sound and i got both i have pacemaker 4495's a high flow 3 inch cat then 3'' into 1 offset magnaflow muffler then 3'' into a fg GT rear system. hmm thanks for that im starting to get an idea of what im looking for 
_________________ Ba Xr6 Boat |
|||
| Top | |
|||
| winman |
|
|||
|
on my ba xr6, ive got pacemaker 4490's -100cpi cat- xforce 2.5" mild steel, i LOVE it to me sounds perfect, not to loud, no drone, sounds mean under acceleration. but everyones different, i suggest going onto youtube and check out some vids of peoples system, this will give you a rough idea on what different set ups sound like
_________________ BA XR6 |
|||
| Top | |
|||
| eattsie9 |
|
|||
|
will do
whats the difference between mild steel or stainless?
_________________ Ba Xr6 Boat |
|||
| Top | |
|||
| winman |
|
|||
|
a big price difference, correct me if im wrong on the following, but i believe stainless steel yields slightly better power due to it not being able to carbon up (in a na 6 i'd doubt you'll be able to feel or measure the power difference) ive also heard they sound "tinny". i went with mild steel on mine, it was cheaper and i prefer the sound.
another bit of info, after about a 1000kms in a mild steel system the note changes to a more deeper slightly louder sound, or simply put, sounds better  . in a stainless system i don't think the note changes, as it doesn't carbon up like mild steel
_________________ BA XR6 |
|||
| Top | |
|||
| eattsie9 |
|
|||
|
winman wrote: a big price difference, correct me if im wrong on the following, but i believe stainless steel yields slightly better power due to it not being able to carbon up (in a na 6 i'd doubt you'll be able to feel or measure the power difference) ive also heard they sound "tinny". i went with mild steel on mine, it was cheaper and i prefer the sound. another bit of info, after about a 1000kms in a mild steel system the note changes to a more deeper slightly louder sound, or simply put, sounds better . in a stainless system i don't think the note changes, as it doesn't carbon up like mild steelhmm thanks heaps ... i much prefer the idea of a good sound
_________________ Ba Xr6 Boat |
|||
| Top | |
|||
| winman |
|
|||
|
yar, just as i said before, check out some youtube vids. 99% of them have s**t sound quality but you can get an idea of what different set ups will sound like. i looked around for about 3 months before i got my zorst fitted lol
_________________ BA XR6 |
|||
| Top | |
|||
| eattsie9 |
|
|||
|
cool ... ye i definetly will ... gonna get rims and a few other little bits and peices done first so ill be lookin around for a while
_________________ Ba Xr6 Boat |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 70 guests |
