|
| krisisdog |
|
|||
|
{USERNAME} wrote: Or go for a setup like I'm about install,....  2 x Eclipse xa1000 @ 480wrms each @ 2 ohm 1 x Eclipse 12" 2ohm dvc sub  Bah - Alpine 1000rms into a big phat 750rms Clarion. that s**t goes fkn loud and low. 
I think its been established for a while now that you wired them wrong champ - I know I said it back on the first page. |
|||
| Top | |
|||
| tx5_reaper |
|
||
|
no i didnt wire them wrong and no the mtx cant do a 1ohm when bridged its only 4ohm it cant even do 2ohm thats why i had the both subs bridged to even it out so it can do a 2ohm stable load but i geuss the amp didnt like it
_________________ !* Banned *! |
||
| Top | |
||
| 66 coupe |
|
||
|
{USERNAME} wrote: no i didnt wire them wrong and no the mtx cant do a 1ohm when bridged its only 4ohm it cant even do 2ohm thats why i had the both subs bridged to even it out so it can do a 2ohm stable load but i geuss the amp didnt like it
Heres some basic ohms law... 2 subs, 4 ohm each if they are in parallel, then you have an 8 ohm load if they are in series, then you have a 2 ohm load. If the amp is bridged, then the amp will effectively see half that impendance per channel. Your amp is not 1 ohm stable per channel, or 2 ohm stable bridged, thats why its cutting out because your overloading it Your amp will only support a 4 ohm load in bridged mode. So your best configuration is either one sub in bridged mode, or 2x subs in stereo mode It is not that your subs "cant do a 1ohm when bridged its only 4ohm it cant even do 2ohm thats why i had the both subs bridged to even it out so it can do a 2ohm stable load" 
Basically its been stated before, you need a better amp fullstop. |
||
| Top | |
||
| grub73 |
|
|||
|
Dude, If you don't want to listen to peoples advice, DON'T ASK FOR IT!
and thank you 66 coupe , but i just don't think he gets it. 
_________________ EF XR6 5spd 14.57@97mph |
|||
| Top | |
|||
| zxhoon |
|
||
|
{USERNAME} wrote: Heres some basic ohms law... 2 subs, 4 ohm each if they are in parallel, then you have an 2 ohm load if they are in series, then you have a 8 ohm load.
|
||
| Top | |
||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
{USERNAME} wrote: nope no dodgy earth the subs are actually bridged at a 2ohm stable and it worked fine with the subs on each channel so im geussing is that my alternator isent keeping up with the flow..... blah blah
your not fukin listening Your amp will run happily with a 4ohm sub on each channel or a 2ohm sub on each channel, or a SINGLE 4ohm sub BRIDGED BUT NOT TWO 4OHM SUBS BRIDGED BECAUSE IT WILL SEE 1OHM WHICH IS NOT STABLE FOR YOUR AMP I think this has been mentioned many times, but you insist on telling us your alternator is at fault |
||
| Top | |
||
| grub73 |
|
|||
|
Basically, to make it easier for you to understand, it's like you are trying to tow a truck (your subs)with a Datsun 120y (your amp). The Datto will cope for a while but will end up f**k!!!!!!!
_________________ EF XR6 5spd 14.57@97mph |
|||
| Top | |
|||
| halo |
|
||
|
nah tx5 i still have the mono and the sub and the 4 way
if you wanna listen to the sub you can come by some time since all i have to do is unplug thr 15" kicker and plug the other one back in, from the setup you currently have you will be impressed. i'm not 100% sure of selling the mono at the moment though, but the sub and 4 way is the same offer as before, 80 each or 150 for both... and no i never got your pm
_________________ the rearing serpent sports in the mists
|
||
| Top | |
||
| grub73 |
|
|||
|
"if you wanna listen to the sub you can come by some time since all i have to do is unplug thr 15" kicker and plug the other one back in, from the setup you currently have you will be impressed."
Mate,I think this guy would be impressed by a properly set up 10" sub
_________________ EF XR6 5spd 14.57@97mph |
|||
| Top | |
|||
| tx5_reaper |
|
||
|
stuff this i will just make a video
_________________ !* Banned *! |
||
| Top | |
||
| 66 coupe |
|
||
|
video of what? what do you want to prove? that your amps cutting out because its underpowered, and you have it running a 1 ohm load? thats already been confirmed for you....
Last edited by 66 coupe on Wed Apr 23, 2008 6:10 pm, edited 1 time in total. |
||
| Top | |
||
| 66 coupe |
|
||
|
double post.
|
||
| Top | |
||
| tx5_reaper |
|
||
|
http://www.youtube.com/watch?v=f8waxN1sRIg
subs as yous say clipping. http://www.youtube.com/watch?v=FHJlU4fDW24 subs acting normal but not punchy
_________________ !* Banned *! |
||
| Top | |
||
| grub73 |
|
|||
|
cood yo do s al a fava maaate and TAKE THE f**k ADVICE!!!! the amp isn't s**t nor are your subs, hook up the MTX to the amp by itself (bridged) which will give the sub about 140wrms instead of 55wrms and the amp will cope better and sound better.
_________________ EF XR6 5spd 14.57@97mph |
|||
| Top | |
|||
| zxhoon |
|
||
|
is that the subs distorting like all f**k or is it the bass on the recording distorted? coz that sounds f**k horrible...
and the subs dont look like theyre moving much at all either? my 10" bounces quite a bit when i crank it and it sounds fine and no clipping... |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 16 guests |
