|
| skidder |
|
|||
|
ok, i have a DVC sub thats currently running off a monoblock, with one voice coil running off each output channel...is this running at 4ohms?
How do i wire my sub so it runs at 2 ohms (as i've always had it running at 4ohms)? Do i run one output channell to the first voice coil, then run wires from there to the other voice coil's same polarity? eg amp+ --> sub+ (1st voice coil) --? sub+ (2nd voice coil) amp- --> sub- (1st voice coil) --? sub- (2nd voice coil) Ohh, yeah each voice coil is 4ohms cheers nick
_________________ {USERNAME} wrote: Cramping in the hand from having it on your Wang for an excessive period of time is a definate con. Seriously do people google "f**k up modifications for Fords owned by Jews" and get linked straight to this site nowadays? AU,factory fitted tickford kit/IRS, t5,Sports ryder/KYB: gone. Last edited by skidder on Sun May 27, 2007 9:52 am, edited 1 time in total. |
|||
| Top | |
|||
| Stone |
|
||
|
Most monoblocks will have 2 outputs for ease of connection of 2 subs or 2 voice coils. The outputs are internally wired in parallel, so two 4 ohm subs or 4 ohm coils will be a 2 ohm load on the amp.
Your amp is wired to 2 ohm. The other way to do it is link the +'s on the sub and -'s on the sub and run the wires to one output on the amp. This still gives a 2 ohm load and uses slightly less wire 
|
||
| Top | |
||
| skidder |
|
|||
|
madness, cheers.....i also HAVE ANOTHER QUESTION
how do i remove the moulded carpet bits from the sides of the boot in an el? Are there just a few of those plastic screwthings that i rip out? cheers
_________________ {USERNAME} wrote: Cramping in the hand from having it on your Wang for an excessive period of time is a definate con. Seriously do people google "f**k up modifications for Fords owned by Jews" and get linked straight to this site nowadays? AU,factory fitted tickford kit/IRS, t5,Sports ryder/KYB: gone. |
|||
| Top | |
|||
| millard455 |
|
|||
|
yep. just rip them plastic clips out (4 of them per side i think)
_________________ EL XR8 SERIES 2, 5SPD, HOT CHILLI RED, 200 ODD RWKW OF V8 FUN AND GAMES |
|||
| Top | |
|||
| gros20 |
|
||
|
yep its easy to remove carpet.
as for subs u have few options get amp with 2 channals (one for each coil amp must support 4 ohm) or parrall up teh voice coils (to get 2ohm) 2ohm would be the way get large monoblock (will ahve one out put hence name) |
||
| Top | |
||
| skidder |
|
|||
|
yeah i have a monoblock and i realised that the 2 output channels are internally wired in parallel...so running at 2ohms now
_________________ {USERNAME} wrote: Cramping in the hand from having it on your Wang for an excessive period of time is a definate con. Seriously do people google "f**k up modifications for Fords owned by Jews" and get linked straight to this site nowadays? AU,factory fitted tickford kit/IRS, t5,Sports ryder/KYB: gone. |
|||
| Top | |
|||
| joolz |
|
|||
|
Parallel connection is as easy as the connecting the positives from both subs together and the 2 negatives together, from there connect the pos and neg to appropriate terminals on the amp.
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 29 guests |
