|
| scottr33gtst |
|
||
|
OK, a question sorta relating to the topic at hand in this thread
http://www.fordmods.com/forums/viewtopic.php?t=24376 i now no that these rims http://www.tempetyres.com.au/products_c ... art_no=180 will fit my ebII xr8 on superlows with spacers (or hub thingys?). i just had a look at my xr today and i saw this: 
that arm or whateva it is is aprox 1 cm of the tyre now, with 16's on 225/50/r16. So what im asking is will the 19" rims on either 235/35/r19 or 275/30/r19 rub this arm? bearing in mind the car will be dropped lower when on lovells super lows. Last question, where can i get the gaurds rolled and hwo much will it cost, wont this crack the paint and stuff it up? and what will i need to convert these rims form au/ba ofset to e series ofset, hub adapters or spacers of some sort? Here is how low the car is low: 
and here is the clearance at the front 
and at the back 
Help is massivly appreciated, i wana get these rims asap. cheers, scott
_________________ Modified EBII/ED XR8
|
||
| Top | |
||
| EL XR8 |
|
|||
|
The rims will fit, i have had problems, with my 19's scrubbing on the exact same part you're worried about. The tyres will sit extremely close, but mine rubbed when on a little lock. The dumb c***s put spacers on to offset the rim a little. Dodgy little f**k.
Any suspension place should be able to lip/roll your guards. Otherwise, if the tyre does hit the guard, it will probably cut into your tyre, and could bend your guard. If my car wasn't so low, it wouldn't have been a problem with the part (lower ball joint?) that you're referring to. Just depends on how low you want to go really. If the guys doing the work tolip your guards know what they're doing, it shouldn't chip the paint, but it can happen, and it's not really their fault if it does flake off. You would need adaptors to fit the AU/BA offset rims onto your EB. I wouldn't even bother trying to fit 275's on the front. I would almost 100% guarantee they wouldn't clear a thing. Stick with some 235/245's. |
|||
| Top | |
|||
| GlennBA |
|
|||
|
275's go on the rear.. 235/245 will go on the front.
Good luck having them fit without problems though.. I have a feeling they'll hit your upper control arm. |
|||
| Top | |
|||
| scottr33gtst |
|
||
|
Yes i will be putting the skinnier tyres on the front, i dn if the wider ones will even fit on the back, theres no much room behind there, what the widest ppl have fitted on here? mind u 235 is still pretty fat) And about whether they will hit that b*&ch ball joint, if i ask them will it fit and they say yes, and it doesnt will i have my a*** covered?
_________________ Modified EBII/ED XR8
|
||
| Top | |
||
| GlennBA |
|
|||
|
if the place you're getting them from (tempe i assume) say they'll fit and they don't, then i think you'll be covered.
|
|||
| Top | |
|||
| scottr33gtst |
|
||
|
WIKID
_________________ Modified EBII/ED XR8
|
||
| Top | |
||
| veeate |
|
|||
|
id say no to the 275's on the rear as i had 265's on mine and it was dumped in the a** and they scrapped the wheel gaurd...
|
|||
| Top | |
|||
| GlennBA |
|
|||
|
veeate, the rims are 9.5" wide on rear, they need fat rubber.
|
|||
| Top | |
|||
| scottr33gtst |
|
||
|
what rims/tyres do u have veeate
_________________ Modified EBII/ED XR8
|
||
| Top | |
||
| veeate |
|
|||
|
i know they "need" fat rubber but your gonna end up with a scrape / cut line all the way around the tyre, not to mention the annoying noise.....im just letting scott know that theres gonna be issues as ive been there done that
|
|||
| Top | |
|||
| veeate |
|
|||
|
{USERNAME} wrote: what rims/tyres do u have veeate
the ones im talking about (with the 265's) were on my old-school 14" jelly beans which i used to use at the drags.....if your cars dumped on its a**, its gonnna scrape like crazy.... |
|||
| Top | |
|||
| scottr33gtst |
|
||
|
well just some new lovells super lows (which arnt on yet), look at the pic it isnt low at the back, i might have to leave it at this height.... im more worried bout the front ball joint, how did u go with that
p.s thanks for the help cos im ordering tomoz, so i need as much info as possible.
_________________ Modified EBII/ED XR8
|
||
| Top | |
||
| veeate |
|
|||
|
i just had a look at the gaurds...theres about 10 - 12mm that can rolled, so u should be able to put 265's on the rear if you roll the gaurds....
|
|||
| Top | |
|||
| veeate |
|
|||
|
at the hieght the car is now itll only scrape when you drive on bumppy roads and go over curbs etc.....if its gonna have super lows, and be as low as mine then itll scrape constantly
|
|||
| Top | |
|||
| scottr33gtst |
|
||
|
ah k, did u used to have 19's? is that what ur basing all this on is what i mean?
_________________ Modified EBII/ED XR8
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 27 guests |
