|
| SIC_XH |
|
|||
|
im just wondering.. what do you guys think about a bonic blue BA MKII xr6 de badged and dumped?
also i wanted to know pirces of badges incase i dont like it and how much a set of king springs would put me back? thanks guys
_________________ XR8 UTE: Low && Loud Last edited by SIC_XH on Sat Jun 27, 2009 9:47 pm, edited 7 times in total. |
|||
| Top | |
|||
| EB92 |
|
|||
|
A set of King springs is around $260.
Not sure on the badge prices.....try a search on Ebay. |
|||
| Top | |
|||
| blindman |
|
||
|
i like the look of cars that have been debaged and dumped thay have all the clean lines about them.
_________________ BANNED USER! |
||
| Top | |
||
| SIC_XH |
|
|||
|
ah goodo, cause i was abit worried about what it would look like.
so i should take all the badges off the side and the falcon mk2 badges too? and hopefully it'll come up smicko =] any advice for pulling the badges off?
_________________ XR8 UTE: Low && Loud |
|||
| Top | |
|||
| EFFII |
|
||
|
de-badge the rear..leave the ford badge unless your going to high fill it then re-spray it.
de-spoiler dump it but leave the xr badges on the skirts. use a flat head to remove the badges but dont dig into the paint. wax and grease remover will take off all the glue. dont go using a heat gun and rub it off because that ruins the paint (orange peel effect) and will give you a saw hand. |
||
| Top | |
||
| SIC_XH |
|
|||
|
so you reckon just rip the 6 off the sides? but the rest of the back?
and yeah i'll be leaving the ford badges.
_________________ XR8 UTE: Low && Loud |
|||
| Top | |
|||
| Airved |
|
|||
|
I think the XR badges alone would look cool. Not sure about removing the lot. Along with spoiler removal, it'll look like an xt from behind.
_________________ Auto '99 AU Fairmont
|
|||
| Top | |
|||
| SIC_XH |
|
|||
|
yeah im not sure about the spoiler, if i did take it off i would wanna replace it with an force lip cause that would just add to the smoothness after the badges come off.
i deff think pulling the 6 off the side would look good, but i would like a smooth rear end... sounds suss 
_________________ XR8 UTE: Low && Loud |
|||
| Top | |
|||
| EFFII |
|
||
|
{USERNAME} wrote: so you reckon just rip the 6 off the sides? but the rest of the back?
and yeah i'll be leaving the ford badges. do this to your rear end...to me that dosnt look like an xt... leave the xr6 badges on the side skirts though. 
|
||
| Top | |
||
| effalcongli |
|
||
|
wow that car looks wikid!!!
_________________ Pacey 4499 and 2.5 exhaust single muffler |
||
| Top | |
||
| SIC_XH |
|
|||
|
that thing is f**k sexy... i wouldnt mind just pulling the 6 off, becasue everyone knows its a 6 anyways cause theres no bonnet bump lol.
but i'd love to dump my car like that. maybe not so much as mine is a daily driver still. also on another note, lowering, do i just buy a set of king springs and change the coils over? or do i need to do anyhting else? cheers
_________________ XR8 UTE: Low && Loud |
|||
| Top | |
|||
| lil_lincoln |
|
|||
|
with removing badges, dont use a screw driver as there is always that little chance u can ding the paint work, my advice with a fishing line. get it under an edge and work it forward removing the badge. with springs, u will need spring compressors to get the spring apart from the strut, ect your shockers should be fine dpending how low you go.
_________________ |
|||
| Top | |
|||
| Airved |
|
|||
|
Become mates with someone at a workshop and steal their compressor. It's such an easy job to do. Friend of mine and i lowered my car all-round with shocks/springs in about an hour and a half.
_________________ Auto '99 AU Fairmont
|
|||
| Top | |
|||
| Lumpy_Camo |
|
||
|
fihing line is the best no question and it will look sexy i know. good luck
_________________ Go The Mighty Falcon.
|
||
| Top | |
||
| SIC_XH |
|
|||
|
thanks for the advice guys.
now this spring compresser, can i just buy one?
_________________ XR8 UTE: Low && Loud |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 62 guests |
