|
| ebxr82nv |
|
||
|
I want to put a set of clear repeaters on my eb which are the best to use
_________________ 9/98 AU1 XR6hp-about to retire from the road and be reborn on the race track. |
||
| Top | |
||
| jonathon |
|
|||
|
heres the link for the tech doc i will advise you of what ones to use and how to do it
http://www.fordmods.com/forums/documents.php?doc=76 i have used the ones that is says to in the tech doc
_________________ Owning 1 of 84,847 ebII. |
|||
| Top | |
|||
| BuNtEr |
|
||
|
AUIII side clear repeaters
_________________ BANNED |
||
| Top | |
||
| Tezza Bear |
|
|||
|
i brought AU111 side repeaters from ford the other day $19 each a bit pricey & about a 10 minute job to fit & looks a hole lot better then the amber ones
_________________
|
|||
| Top | |
|||
| BuNtEr |
|
||
|
ebxr82nv wrote: I want to put a set of clear repeaters on my eb which are the best to use
if you get AUIII DONT CUT THEM like it says to in the doco you dont need to.
_________________ BANNED |
||
| Top | |
||
| EFFII |
|
||
|
can someone get me a link for the ef/el
|
||
| Top | |
||
| EFFII |
|
||
|
dw about that^^
|
||
| Top | |
||
| Chicken |
|
|||
|
BuNtEr wrote: AUIII side clear repeaters
AUI is easier/cheaper, as you don't have to chang the bulb.
_________________ Red goes faster, and chicks drive better |
|||
| Top | |
|||
| Leroy |
|
||
|
Chicken wrote: BuNtEr wrote: AUIII side clear repeaters AUI is easier/cheaper, as you don't have to chang the bulb. the $2 bulb? i think the clear ones look better. though the Fairmont ones had a clear outer and there was an amber inside it so you still use the same clear bulb
_________________ Now driving a Hilux |
||
| Top | |
||
| NCIILANE |
|
|||
|
I recently did mine and asked all the same questions you did. Here is my post on the subject with the end result being the fitting of the AUIII Fairmont Ghia set and new orange globes. Came up shmick IMO.
http://www.fordmods.com/forums/viewtopi ... highlight=
_________________
|
|||
| Top | |
|||
| NCIILANE |
|
|||
|
BuNtEr wrote: ebxr82nv wrote: I want to put a set of clear repeaters on my eb which are the best to use if you get AUIII DONT CUT THEM like it says to in the doco you dont need to.
_________________
|
|||
| Top | |
|||
| bArNsY |
|
|||
|
don't bother doing this mod unless you put them on the right way, and this means cutting the repeater as per the tech doc, unless you like people laughing at you because you put it on back to front.
_________________ FG G6E Turbo |
|||
| Top | |
|||
| NCIILANE |
|
|||
|
bArNsY wrote: don't bother doing this mod unless you put them on the right way, and this means cutting the repeater as per the tech doc, unless you like people laughing at you because you put it on back to front. I was going to bite, but I will leave that up to you BuNtEr 
_________________
|
|||
| Top | |
|||
| BuNtEr |
|
||
|
bArNsY wrote: don't bother doing this mod unless you put them on the right way, and this means cutting the repeater as per the tech doc, unless you like people laughing at you because you put it on back to front.
as i have said b4 you DONT need to butcher them by cutting them to make them fit you DONT NEED TO. look at my EB i have them they are on the right way and i didnt need to cut them. ok in English No cutty the repeater ok !!!!!!..... Only thing that needs to be cut is the 2 lugs on the rubber plug that holds the globs, that’s were the cutting should stop ok. Also if a person wants them the other way around and likes them that way its ok too, no rule on how they should be facing each to there own. its not cheap if you cut one and stuff it up, it would piss me off if i knew i didn’t have to cut them, and they would have fitted just buy heating the base of the springing part and move it back a poofteenth then push it in .
_________________ BANNED |
||
| Top | |
||
| NCIILANE |
|
|||
|
BuNtEr wrote: bArNsY wrote: don't bother doing this mod unless you put them on the right way, and this means cutting the repeater as per the tech doc, unless you like people laughing at you because you put it on back to front. as i have said b4 you DONT need to butcher them by cutting them to make them fit you DONT NEED TO. look at my EB i have them they are on the right way and i didnt need to cut them. ok in English No cutty the repeater ok !!!!!!..... Only thing that needs to be cut is the 2 lugs on the rubber plug that holds the globs, that’s were the cutting should stop ok. Also if a person wants them the other way around and likes them that way its ok too, no rule on how they should be facing each to there own. its not cheap if you cut one and stuff it up, it would piss me off if i knew i didn’t have to cut them, and they would have fitted just buy heating the base of the springing part and move it back a poofteenth then push it in .  Even though I did cut mine (because nobody told me not to and I wish they had) I was observant enough to only cut half of the spring edge. And yes bArNsY, if you look at the pic's in my post, mine are on the right way!
_________________
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 22 guests |
