|
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Has anyone got a photo / measurement or both of what that rear bumper retainer looks like?
Mine went missing , I plan to make one. I wont be paying $55.00 for one from the wreckers in Qld. I have a 2mm thick aluminium plate. Thanks, Bondy |
||
| Top | |
||
| Mad2 |
|
|||
|
bondy99 wrote: Has anyone got a photo / measurement or both of what that rear bumper retainer looks like? Mine went missing , I plan to make one. I wont be paying $55.00 for one from the wreckers in Qld. I have a 2mm thick aluminium plate. Thanks, Bondy hey Bondy - sedan? as i'm not sure what/which retainer you mean. |
|||
| Top | |
|||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Mad2,
Thanks for your reply. The item, could be named differently but though it was a bumper retainer. On the Ford AU2 Sedan it's a piece of metal that sits under the rear bumper bar and goes from the bumper bar to the underside of the wheel well. From what I gather it is or was held in position with 4 rivets. 2 at the bumper bar and the other 2 rivets would have been at the wheel well. It's positioned somewhere between the middle and towards the tail pipe, but underneath the bumper bar. Cheers |
||
| Top | |
||
| Mad2 |
|
|||
|
bondy99 wrote: Mad2, Thanks for your reply. The item, could be named differently but though it was a bumper retainer. On the Ford AU2 Sedan it's a piece of metal that sits under the rear bumper bar and goes from the bumper bar to the underside of the wheel well. From what I gather it is or was held in position with 4 rivets. 2 at the bumper bar and the other 2 rivets would have been at the wheel well. It's positioned somewhere between the middle and towards the tail pipe, but underneath the bumper bar. Cheers yep sounds similar to what's on her BF sedan. just look at 'where' it was mounted [holes in bumper/wheel well] & go from there.......... otherwise i'm hoping to go back to wreckers & can checkout the piece then if needed. 
|
|||
| Top | |
|||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
G'day Mad2,
Here's a photo of mounting position. You'll have to go to the link to see pic. https://i.postimg.cc/7Z2wkw7z/Place-of- ... tainer.jpg Cheers, Bondy |
||
| Top | |
||
| Mad2 |
|
|||
|
bondy99 wrote: G'day Mad2, Here's a photo of mounting position. You'll have to go to the link to see pic. https://i.postimg.cc/7Z2wkw7z/Place-of- ... tainer.jpg Cheers, Bondy ok. yours  what i found & going from rivet centre to rivet centre on first two pics.     hope that helps ya Bondy |
|||
| Top | |
|||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Mad 2
Thanks mate, now I got something to go by. Cheers, Bondy |
||
| Top | |
||
| Mad2 |
|
|||
|
with the first two pics, i think it was 'about' 155mm between the rivets. i couldn't get the camera where i wanted it to show length clearly.
Goood luck with it
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 28 guests |
