|
mrnasty |
|
|||
|
Anyone know how to get the falcon/gli badge off the back of an EF under the tail lights? im replacin it with a little tickford badge, but i dont wanna jam a screw driver in and snap them out if theirs an easier way.
_________________ Cougar Zero makes my pants fit nice. |
|||
Top | |
Leszek |
|
|||
|
most people that i know of just took it off with their fingers or carefully with a screw driver. it pretty much just stuck on with double sided tape or some other type of ahesive
_________________
|
|||
Top | |
Rapier |
|
||
|
heat it up with a hair drier will come of much nice and easier as well
|
||
Top | |
azza |
|
|||
|
just pull off with hands.... did mine then polished it up and left no mark.
_________________ BA XR8 manual ute black |
|||
Top | |
ruthless |
|
|||
|
i just did mine, thought it'd never come off clean but it ended up being spotless!
dipped a rag in boiling water and held it on the badge until glue was probably warm behind the badge (hairdryer works too).. then used some tooth floss to get it off, came off nicely then cleaned with some degreaser/soap and a lil bit of scrubbing
_________________ EF II I6
|
|||
Top | |
Thomas |
|
|||
|
Okay lad, i did mine i think i did it pretty good no marks no scratches.
1. Get a rag dip it in boiling water and go other the badge. 2. Then it should get a bit hot on the metal and you can feel it sliding. 3. Get some dental floss, slip it in from one side and drag, it comes off perfectly no scratches. Note you must use dental floss. Here are the results. Although now i have a XR tickford combination...
_________________ 237.9 KW ATW
|
|||
Top | |
ReGiE |
|
|||
|
i just used a hairdryer and screwdrive on my 4.0l bades on the guears
_________________ Gooooone - Eb2 Coon - 143RWKW |
|||
Top | |
mrnasty |
|
|||
|
sweet, will do. i always thought their would be holes left by the falcon badge on the back. cool!
_________________ Cougar Zero makes my pants fit nice. |
|||
Top | |
1 SLY 97EL |
|
|||
|
Snow_white wrote: Okay lad, i did mine i think i did it pretty good no marks no scratches.
1. Get a rag dip it in boiling water and go other the badge. 2. Then it should get a bit hot on the metal and you can feel it sliding. 3. Get some dental floss, slip it in from one side and drag, it comes off perfectly no scratches. Note you must use dental floss. Here are the results. Although now i have a XR tickford combination... Yeah I thought the actual "Falcon " badge was bolted in. But hey that looks kool Snow white have got me thinking now. maybe the Rear " Ford " badge is bolted in maybe
_________________ " In life their is never an Obligation just an Opportunity to..Own an awesome 1970 Ford Mach 1 Mustang! " |
|||
Top | |
Thomas |
|
|||
|
Yes the rear is held down with pins. If you remove it there will be holes in the back not a good look.
_________________ 237.9 KW ATW
|
|||
Top | |
rockerfella |
|
||
|
yes, as i have just discovered.
what's the best way to a) clear up the left over s**t the adhesive leaves b) cover the holes!
_________________ \m/ |
||
Top | |
Rapier |
|
||
|
rockerfella wrote: yes, as i have just discovered.
what's the best way to a) clear up the left over s**t the adhesive leaves b) cover the holes! scrub scrub scrub lol pain in the a** it is |
||
Top | |
Tomek |
|
||
|
Rapier wrote: scrub scrub scrub lol pain in the a** it is
Would it be easier if the glue was heated up??? |
||
Top | |
Rapier |
|
||
|
Tomek wrote: Rapier wrote: scrub scrub scrub lol pain in the a** it is Would it be easier if the glue was heated up??? yep use a hairdrier rub it with ure finger real fast and it will come off |
||
Top | |
mrnasty |
|
|||
|
got mine off, left two holes where the falcon badge was, the tickford wing covered them both though. I had a bit of that adhesive s**t on their, i rubbed a little bit of that kevs goo remover on a cloth and it all came off, looks nice and clean now.
_________________ Cougar Zero makes my pants fit nice. |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 57 guests |