|
muscle_18 |
|
||
|
Hi,
when i bought my car, the left side demister connector was broke, and there was no possible way to resolder it back cause the person who i bought it off, scratched all the copper off. So i bought some of that Silver Hardner demister repair that connects the demister back to the window. it connected fine and i tested the circuit and it was conducting. 1 week later, when i turned it on the rear windscreen blew up, and the glass all shattered. Now i need a new window. The wreckers has one for 50 buks. he said all i gotta do it take out my old window, remove the existing mould, clean the surface, then i can just place the 2nd hand windscreen on and use that special Black silicon glue to stick the window back down. Is this correct what he has said? also will a EA-EB windscreen fit for a ED? Thanks fellas! |
||
Top | |
Interceptor |
|
||
|
pretty much it
EA-ED rear screens are all the same be careful removing the old screen cos they break VERY f**k easily
_________________ Banned |
||
Top | |
muscle_18 |
|
||
|
Interceptor,
ive already removed the old windscreen, removed the moulds, just gotta clean the edges to ensure the glue will stick. i just found out what glue to use. Sikaflex-255 Extra, australian product for glazing windows. Would anyone know roughly how much this product is and where? Thanks !!! |
||
Top | |
Interceptor |
|
||
|
gah
soz, meant to say "be careful removing the replacement rear screen" who's pulling the replacement screen out? the sikaflex is available at mitre 10 IIRC
_________________ Banned |
||
Top | |
madmax |
|
|||
|
{USERNAME} wrote: Now i need a new window.
use that special Black silicon glue to stick the window back down. Is this correct what he has said? also will a EA-EB windscreen fit for a ED? Thanks fellas! It's not Silicon, it's Polyurethane and you need to get the right one Sikaflex® -255 is for bonding of windscreens Go to {DESCRIPTION} This site also has instructions on changing a windscreen
_________________
|
|||
Top | |
muscle_18 |
|
||
|
the windscreen has already been removed by the wreckers.
all im gona do is clean the extra mould off it, then pump Sikaflex® -255 thanks |
||
Top | |
Interceptor |
|
||
|
if all else fails, try panelbeaters or paint supply shops....
_________________ Banned |
||
Top | |
Black Betty |
|
||
|
We buy the sikaflex at about $13 a tube, you should get a special nozzile with it that has a v taken out of the end, when applying the urethane have the v facing away from the direction that you are going and the gun nearly upright, you will want the urethane to be about 15mm high and come to a point all the way around, sit the screen in line it up and then push it down around the edges.
|
||
Top | |
TURBO_GHIA |
|
|||
|
where did you get the Silver Hardner demister repair??
_________________ HMMMM BOOST !!!
|
|||
Top | |
Smokey...Retired! |
|
|||
|
Hey! I just put my rear window on the EA & its leaking at the top! I been trying to re seal it but it still leaks...tell me how u go!
_________________ Blast from the past..... |
|||
Top | |
Black Betty |
|
||
|
{USERNAME} wrote: Hey! I just put my rear window on the EA & its leaking at the top! I been trying to re seal it but it still leaks...tell me how u go!
It is very hard to fix a leaking windscreen when it hasnt been installed properly thats why your better off letting a pro do it, they would probably only charge $40 to do it. The only advice that I can offer you is to take the top mould out and fill the gap up along the entire top edge with urethane and then chuck the mould back in. |
||
Top | |
muscle_18 |
|
||
|
EDMONTY
i bought it from supercheap auto for around 20 buks. thats what caused my windscreen to explode i think. I called around, and got some window repair guy to come and install my windscreen. he charged 77 buks...he came to me, cleaned the window from the old mould, used a primer, stuck the windscreen on, and replaced the top rubber seal. best to pay the small fee and get someone to do it properly, if you are not sure of what to do. |
||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 32 guests |