|
| JakLTD |
|
||
Age: 38 Posts: 60 Joined: 21st Dec 2008 Ride: Ford DC LTD, EA Falcon GL Location: Melbourne |
Here's mine. Not sure what it is but I like it since I'm not a fan of big blingy wheels
 
|
||
| Top | |
||
| Jonathan Kakousidis |
|
|||||
|
heres mine on my new el xr6
they are mark2 ba xr8 17x8 powder coated "night sky"
_________________ MY BABIES |
|||||
| Top | |
|||||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
youll have to keep the tyre shine up on those !!
|
||
| Top | |
||
| jpw1177 |
|
||
|
Just a bit of info, all the wheels supplied factory for the FPV's and XR's are made in China. I would not be surprised if the copies are made in the same factory as the originals for Ford.
During FG Development, it was discovered the supplier in China of the FPV / XR wheels had the new FG ones up on there website months before any photos of the car were released. Thankfully it was that difficult to find the website, no one did. They were listed as being on sale too, when we translated the Chinese. Would have been interesting if someone had actually found the site and purchased some. Still one of my favourite e-series wheels are the FBT Speedlines. I have a set sitting in my garage ready to go on the XG Panelvan I am doing up. |
||
| Top | |
||
| crankah |
|
||
|
 
|
||
| Top | |
||
| Rick_Deckard |
|
|||
|
Are these aftermarket ones drying up or what? I search pre-au etc. on ebay every now and again and the results seem to be shrinking every time.
_________________ E39 523i |
|||
| Top | |
|||
| phatEB |
|
||
|
seems to be no imagiation with rims these days, Every kent buys a Pre AU and must fit FPV copies to it. screw that!!!
Most jap rims fit pre aus. Just gotta get good offset. like 0 offset or +6. |
||
| Top | |
||
| Lowlane7 |
|
||
|
{USERNAME} wrote: seems to be no imagiation with rims these days, Every kent buys a Pre AU and must fit FPV copies to it. screw that!!! Most jap rims fit pre aus. Just gotta get good offset. like 0 offset or +6. hmmm. That just opened a whole new search category. Nissan 5 stud rim.....
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| phatEB |
|
||
|
belive it or not, Nissansilvia.com is a welth of Rims that will fit fords. and look sweet.
Thats where I got my drift teks |
||
| Top | |
||
| Lowlane7 |
|
||
|
{USERNAME} wrote: belive it or not, Nissansilvia.com is a welth of Rims that will fit fords. and look sweet. Thats where I got my drift teks as long as they have a 0 - +6 offset. If you can find the right set they don't look too bad.
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
then have the hubs machined out to 71mm
and also make sure the wheel is load rated to your falcon, as opposed to a midsize Jap box which is was intended for...... |
||
| Top | |
||
| phatEB |
|
||
|
drift teks have mass hubs anyway. and most jap rims s**t on fords rims for strengh. as long as they are genunie. Not some crap copy.
I want some Work Minster Mk3's in 18x 10 and 18x12 for mine at some point. -10 offset to sit them right. |
||
| Top | |
||
| Lowlane7 |
|
||
|
Will 10 inch wide rims even fit under the gaurds of an E series, let alone 12s!!
If so tho, I'm goin 8s on the front and 9 or 10 rears if the dish is big
_________________ [color=#004080]Cheers, Jacob. |
||
| Top | |
||
| phatEB |
|
||
|
10s fit on the rear fine. from what Ive seen. Mine are 9.5s all round and fit fine. so extra .5 of a inch easy.
|
||
| Top | |
||
| Rick_Deckard |
|
|||
|
I'm seriously considering hub centric hub adapters and some nice rims. I love multi-spoke rims and these Ford copies are not what I'm after to.
_________________ E39 523i |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 52 guests |
