|
| Philchars |
|
||
Age: 39 Posts: 108 Joined: 20th Mar 2010 Ride: 2002 Au Ford Falcon Ute Location: Morayfield |
Hey all, simple question... whats the best way to take off a tire the rim? no need to keep em there being tossed... all the air is out of them... i tried breaking the seal off with a big screw driver... but no go... i dont have the correct tools for the job so makes it harder...
|
||
| Top | |
||
| phongus |
|
|||
|
Ash wrote: Easiest way is to have someone with a machine to take them off. Saves a lot of sweat and all your neighbours hearing you swear. Or you can cut them off by cutting the tyre through and then cutting the bead. The bead is a C*** to cut. That s**t is hardened steel and won't budge without a fight. I suggest you try and break the bead in anyway possible. You can make a tool using timber you have lying around. I managed to break the bead by using the end of a trailer, with a piece of cloth wrapped around the hitch, letting it rest on the tyre and then jumping on the trailer...hard part was holding the rim/tyre steady while jumping on it. I was doing this on my race bike rims/tyres, so it may have been easier since they are some what thinner. If not, I'd take it to a tyre place and get it removed...they might do it for free.
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Philchars |
|
||
Age: 39 Posts: 108 Joined: 20th Mar 2010 Ride: 2002 Au Ford Falcon Ute Location: Morayfield |
well fuk!
lol didnt think it was going to be that bad... guess i'll take it down to the tire shop!Cheers |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Angle grinder , my mate did it, bit messy tho . and u get the lovely smell of burning rubber lol
_________________ El XR6 Turbo |
|||
| Top | |
|||
| phongus |
|
|||
|
ef_falcon_95 wrote: Angle grinder , my mate did it, bit messy tho . and u get the lovely smell of burning rubber lol the bead is rather close to the rim, so could damage the rim like that. You could also build you're own bead breaker using large pieces of timber...unless you know how to weld you can use steel bars... here are some examples..... http://www.youtube.com/watch?v=GKuCjMvE4Og http://www.youtube.com/watch?v=ztYmUgGBObk I would say the steel one is much sturdier haha.
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Troy |
|
||
|
i've tried doing it, it's a b**ch. then i learned my mate had an older tyre machine.
i would suggest just to take it to a shop. much less hustle |
||
| Top | |
||
| phatba |
|
||
|
tyre shop job, they wont damage your rim, and they will dispose of the tyre for the princely sum of about $5
|
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
phongus wrote: ef_falcon_95 wrote: Angle grinder , my mate did it, bit messy tho . and u get the lovely smell of burning rubber lol the bead is rather close to the rim, so could damage the rim like that. You could also build you're own bead breaker using large pieces of timber...unless you know how to weld you can use steel bars... here are some examples..... http://www.youtube.com/watch?v=GKuCjMvE4Og http://www.youtube.com/watch?v=ztYmUgGBObk I would say the steel one is much sturdier haha. The tyre he cut off the rim, well he wasn't going to use the rim , so yeah rim was a bit damaged
_________________ El XR6 Turbo |
|||
| Top | |
|||
| low_ryda |
|
|||
|
you can break beads with a bottle jack,something heavy and a bit of ingenuity
 i made a jig to suit a hayman reece towbar arrangement and bottle jack to break tyre beads. generally the higher profile the tyre the less force it requires as theres more sidewall flex. not sure if the width affects it. it's actually a little unsettling when you figure out how easy it is to pop it when the force is applied in the right way.
_________________ Not to get technical, but according to chemistry alcohol is a solution. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 68 guests |
