|
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
G'day,
I purchased anoter bootlid from wreckers and yes, it has bubble rust on the lip i..e underneath the lid. As it looks straighter and not bent like the one I currently have. it needs to be welded. I've got a MIG Welder with Argoshield gas. I've welded before but not skillful enough to tackle light stuff on cars. Is there anyone can give me a hand on this? I'm in Eagleby. near Beenleigh, which is half-way between Brisbane and the Gold Coast. I'm not after a Pro but someone who can do the job on the cheap. Cheers, Peter |
||
| Top | |
||
| OZBMX |
|
|||
|
couldn't you get any good ones?
well anyway how bad is the rust you might be able to just grind it back and put some rust kill on prior to respraying it. might be worth post a pic of how bad it is
_________________ Signature removed by moderator.signature must not exceed 120x500 pixles |
|||
| Top | |
|||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
{USERNAME} wrote: couldn't you get any good ones? well anyway how bad is the rust you might be able to just grind it back and put some rust kill on prior to respraying it. might be worth post a pic of how bad it is G'day OZBMX, Yeah, could not find any the rigfht colour, been to a few wrecking yards and most have been damaged as in twisted and worse than mine, others missing completely...must be a popular item. You can feel the rust underneath the fingers when the bubble squashes and you can hear the crunching noise. I'll take a few pics and post it here, I'll take a few pics today sometime. It could be uploaded today or tomorrow. Cheers, Peter |
||
| Top | |
||
| bondy99 |
|
||||||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
As promised earlier.
Here are the photos, I placed my fingers inside the inner area and yes you can feel the roughness / rust coming through so it needs to be cut and welded with zincanneal or similar. I need to keep this car for another 10 years. Cheers
|
||||||
| Top | |
||||||
| frd906n |
|
||
|
hmmm looks quite bad actually, but looks doable, mater of cutting it out and re welding a new peace of the body panal back in,
Has the rust gone right through to the out side?
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
No, the rust is contained to the inner or should say underneath the lid. it has not ventured to the outer or outside panel. Bit hard trying to describe it via texting, might be easier for me to bring it over to you to see.
|
||
| Top | |
||
| frd906n |
|
||
|
looks simple enough to do, if not i can set up my tig welder to do it
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Ok, might be simple for you as you have the knack whereas for me I dont seem to have the knack.
Cheers |
||
| Top | |
||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
I think your Tig welder might be the go as my Mig may not handle such a thin metal even though its has 0.6mm mild steel wire.
PM sent earlier |
||
| Top | |
||
| frd906n |
|
||
|
geez thats thin, should be fine, long as i set it right before hand
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| OZBMX |
|
|||
|
G'day OZBMX,
Yeah, could not find any the rigfht colour, been to a few wrecking yards and most have been damaged as in twisted and worse than mine, others missing completely...must be a popular item. [/quote] You would not believe it but I just scrapped a lid in that colour on the au, it's had spoiler holes though, but otherwise. If you want a spare rear bar mate let me know, your not that far from me either.
_________________ Signature removed by moderator.signature must not exceed 120x500 pixles |
|||
| Top | |
|||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
OZBMX,
It's okay, I still would have to weld the holes anyway. Not keen on having spoilers on the boot but thanks anyway. Cheers |
||
| Top | |
||
| frd906n |
|
||
|
ur boot lid is the straightest one i have seen, all the others at the wreckers are rooted,
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Thanks frd906n
Let me know when you can get down here on Thursday. Dentist 10.00am to 11.00am at least. Quacks at 2.30pm Cheers |
||
| Top | |
||
| Froudey |
|
||
|
just kill rust it and fibreglass it
_________________ R.I.P Tobias my son. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 21 guests |
