Fordmods Logo

BA/BF into AU how hard... 

 

Page 1 of 1 [ 8 posts ] 

 
 Post subject: BA/BF into AU how hard...
Posted: Sat Oct 09, 2010 1:50 am 
Fordmods Junkie
Offline
User avatar

Age: 45

Posts: 1000493

Joined: 6th Nov 2004

Gallery: 2 images

Ride: AUXR6 HP With Ducati SupA Bike!

Location: Perth
WA, Australia

ok so i love my AU and it getting on with 275kms!
insides are a looking worn and it needs more go
and a good B series inside would look good with AU XR outsides!
and have been thinking that since the B series from the firewall back is basically the same car
how hard would it be to transplant the whole insides of a b series car into an AU ?
im talking about fitting up the dash and seats etc
door trims should be piss easy

and yes at the same time i would drop in the B series engine/trans and front brakes :)

so all wiring looms would match and be running the b series ecu

i know i would need to plsice int eh front headlights/rear tail lamps and indicators etc

is there anythign else i am missing?


cheers

 

_________________

RIP SCOTT

Top
 Profile  
 
 
 Post subject: Re: BA/BF into AU how hard...
Posted: Fri Oct 22, 2010 12:20 am 
Stock as a Rock
Offline
User avatar

Age: 37

Posts: 110

Joined: 29th Jul 2005

Ride: BA XT

Location: melbourne
VIC, Australia

A lot of drilling in your firewall to fit the very different BA airbox assembly and brackets to fit the dash up to the firewall. Your door trims will be a straight swap. BA Door = AU Door, all you need to do is rip out the AU looms and but BA ones in. Seats I think need a few modifications to the rails. Back seat brackets also need to be modified, and the rear floor under the rear seat base is lower on the AU than on the BA.
Top
 Profile  
 
 
 Post subject: Re: BA/BF into AU how hard...
Posted: Sun Oct 24, 2010 12:49 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 4143

Joined: 7th Dec 2004

Gallery: 6 images

Ride: E39 523i / EF Fairmont

Location: Brisbane
QLD, Australia

Yeah this is no help, but BAs are going pretttty cheap nowadays.

 

_________________

E39 523i
EF Fairmont

Top
 Profile  
 
 
 Post subject: Re: BA/BF into AU how hard...
Posted: Sun Oct 24, 2010 2:00 pm 
Getting Side Ways
Offline

Age: 34

Posts: 747

Joined: 8th Nov 2009

Ride: ford au

Location: brisbane
QLD, Australia

Didnt ftg autosalvage do something like this,

 

_________________

Daily Driver, Series 1 Au Forte

Quote:
Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors

Top
 Profile  
 
 
 Post subject: Re: BA/BF into AU how hard...
Posted: Sun Oct 24, 2010 5:50 pm 
Getting Side Ways
Offline
User avatar

Posts: 450

Joined: 24th Jan 2009

Ride: BF wagon

Location: western sydney
NSW, Australia

^^Nope but they did put a typhoon motor into a BA wagon and XR front end on it also. was called the Tsunami Wagon and was red.

There is a build thread on here with a complete BA into AU interior swap (cams build ), personally i would just buy a BA/BF wagon. the amount of time and money to transplant it all over and get it running- wouldn't be worth it IMO.
Top
 Profile  
 
 
 Post subject: Re: BA/BF into AU how hard...
Posted: Sun Oct 24, 2010 6:28 pm 
Getting Side Ways
Offline

Age: 34

Posts: 747

Joined: 8th Nov 2009

Ride: ford au

Location: brisbane
QLD, Australia

ford-4l-and-6-cylinder-f1/ba-motor-into-a-au-t39655.html

Bloody comp is playing up

 

_________________

Daily Driver, Series 1 Au Forte

Quote:
Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors

Last edited by frd906n on Sun Oct 24, 2010 6:35 pm, edited 1 time in total.

Top
 Profile  
 
 
 Post subject: Re: BA/BF into AU how hard...
Posted: Sun Oct 24, 2010 6:34 pm 
Getting Side Ways
Offline
User avatar

Posts: 450

Joined: 24th Jan 2009

Ride: BF wagon

Location: western sydney
NSW, Australia

thats not the one i was thinking of. But well done frd906 :lol:
Top
 Profile  
 
 
 Post subject: Re: BA/BF into AU how hard...
Posted: Thu Nov 04, 2010 7:29 am 
Getting Side Ways
Offline
User avatar

Age: 36

Posts: 2159

Joined: 15th Nov 2005

Gallery: 17 images

Ride: TS40

Location: Latrobe Valley
VIC, Australia

FourL6 AU to BA Interior Conversion
i would have been happy with it if i'd put a few more brackets between the firewall and the dash and redone the icc properly...(i never tried swapping the heater box or electrics). but had a little girl, brought a house etc. so the ba dash is sitting in the shed for a few years, the AUs the misses daily atm.

a easier option is a fairmont dash...
Fairmont Dash Conversion

 

_________________

Was - 2001 AUIII Ford Falcon Forte
Genuine T2 TS50 bodykit, 18" BF Cobras, Boge and Eibach Suspension and Complete AU2 Fairmont Ghia Interior

Now - 2012 FG Mk2 Ford Falcon XR6
Swift Green,6 Speed Auto, Stock... and a Fuel Card :)

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 8 posts ] 

Who is online

Users browsing this forum: No registered users and 84 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Mon Nov 18, 2024 4:52 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names