|
| gryph |
|
|||
|
Hey its cold now so i wanna fix my c/c, problems are the temp wont go above 16deg..... im assuming thats just the buttons tho. The major issue is when its on 32 deg say it wont spit out hot air jus the same old cold crap u get on 16..
Any help? |
|||
| Top | |
|||
| phongus |
|
|||
|
Hmm this could mean the heater tap is jammed not allowing any hot coolant to run through the heater core, or your heater core is buggered which means replacing or your blend door motor is kaput not allowing the mixture of hot and cold air.
Easiest to replace is the heater tap...or check if it is still functioning properly. Heater core and blend door motor, requires the whole dash to be remove to gain access to it  . Not a fun job I'll tell you that much.
phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| philaddis |
|
|||
|
I would be thinking it is more likely the blend door or a blocked core....
Only because the default position for the tap (without vacumn) is open..... fingers crossed it is the tap tho..... Have you done a self test yet??
_________________ ED XR8 Spri-mitatio-nt |
|||
| Top | |
|||
| gryph |
|
|||
|
No i havent. Wouldnt really know how to either.... i have the worst manual in history here.....
|
|||
| Top | |
|||
| snap0964 |
|
|||
|
So then visit our ultra informative Tech documents section.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| Nicko |
|
|||
|
snap0964 wrote: So then visit our ultra informative Tech documents section.
Another Free Tip From Snap0964!
_________________ Nicko |
|||
| Top | |
|||
| ALS008 |
|
||
|
Where is this blend valve that you talk about??
|
||
| Top | |
||
| Krytox |
|
|||
|
I take it the LCD display doesn't go higher?
If so, remove the CC unit, dismantle it, clean the button contacts with isopropyl alcohol (medi swab). Also its an idea to re-solder the pin connectors on the face circuit board, These are common to have the plastic housing rub the solder and short each other out.
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| ALS008 |
|
||
|
Where is the location of the Blend Valve, and Cabin temp sensor??
|
||
| Top | |
||
| philaddis |
|
|||
|
Blend door is situated on top of the heater box....to get to it is a dash out job......
The cabin temp sensor is known as a cabin sniffer motor and I'm pretty sure in EF/EL's it is part of the control module. In the EA-ED's it sits next to the trip computer behind that grate!
_________________ ED XR8 Spri-mitatio-nt |
|||
| Top | |
|||
| gryph |
|
|||
|
Cheers guys got it sorted
|
|||
| Top | |
|||
| Krytox |
|
|||
|
what was the culprit?
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| gryph |
|
|||
|
Needed some nail polish remover on the contacts. Is like i never had a problem now
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 73 guests |
