|
| ford383f |
|
|||
|
 pin - colour 1 - orange/yellow - 2 - green/white - 3 - not used 4 - not used 5 - black/brown dash - 6 - not used 7 - not used 8 - pink - 9 - black/brown dash - 10 - brown/black - 11 - green/orange - 12 - white - 13 - not used 14 - white/red - 15 - grey/black - 16 - purple/blue - really need help with my cruise the ef/el guide isnt much use as the ea-ed speed controllers have 16 pin plugs and the ef/el are 10 where do each of these splice into the gli loom to make the cruise control work i have the break switch the two pin plug from the break switch the 3 pin plug is under the bonnet near the washer bottle for the controller i have the wheel and boss with the cruise buttons the vacuume lines the throttle cables the vacuume controller near the break booster the speed controller the pin numbers dont match with the ef/el cruise guide in the tech doco and there arnt any wire colours written in the ef/el guide any help would be great cheers Attachment: File comment: speed control unit + loom
speed1.jpg [ 174.06 KiB | Viewed 250 times ]
_________________ 95' XG |
|||
| Top | |
|||
| BenJ |
|
||
|
You need a workshop manual with the relevant wiring diagrams for the ute, and the EA-ED. Then you can work out the wire colours and where they go.
Alternatively, you can put EF-EL cruise in the ute, but only if you are converting to a BBM manifold. Cheers BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| ford383f |
|
|||
|
ahh so no one on here has wired one in from scratch?
what a pain... would the normal off the shelf gregories/haynes workshop books have it in them? cheers
_________________ 95' XG |
|||
| Top | |
|||
| BenJ |
|
||
|
Yes, they should.
Cheers BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| dazza027 |
|
||
|
There is a tech doument in here I think that has a EF EL manual with the wiring diagram for the Cruise control circuit with wire colours. fordmods-technical-documents-diy-f38/ea-eb-ed-ef-el-nf-nl-ltd-workshop-manual-t86156.html Click the link, has the manual, download as a PDF, I think you have to unzip it.
|
||
| Top | |
||
| BenJ |
|
||
|
Unfortunately, he needs the EA-ED/XG version.
BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| dazza027 |
|
||
|
EA ED Book is on the same page.
|
||
| Top | |
||
| ford383f |
|
|||
|
downloading the pdf's now
_________________ 95' XG |
|||
| Top | |
|||
| ford383f |
|
|||
|
hi benj the eb im wrecking the cruise controller was mounter about the right foot under the dash and had factory loom from what everyone says and what iv found is they are factory mounted under the centre console is it a factory mounting? also got a 88 lane and its not under the center console or above the right foot its above the hand break
anyways thanks for the pdf link spliced into the low series loom make all the right noises but either the vacuume controler is fried or theres a vacuume leak somewhere cause it wount hold the speed cheers
_________________ 95' XG |
|||
| Top | |
|||
| Nigel |
|
||
|
Mate - Factory Pre EB II was under the dash, mounted to the drivers side vent cover plate.
EB II onwards they were mounted under the Console where the Amp goes on Pre EB II nigel |
||
| Top | |
||
| ford383f |
|
|||
|
ahh thanks mate i never looked above the right hand vent for the cruise plug just looked under the console guess i might have spliced into a loom that already has a plug on it somewhere ahwell live and learn i spose
cheers
_________________ 95' XG |
|||
| Top | |
|||
| ford383f |
|
|||
|
cruise is in and working
any idea if the ea/ed indicator stalk will fit onto an xg ute for the boss with the cruise contact? or has the xh ute got the standard ford boss on it? cheers
_________________ 95' XG |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 95 guests |
