|
| OBS35N |
|
|||
|
i have just tried to install my gear knob and shifterboot for my ef which i have converted to a manual. now this is the problem..... they dont f**k fit. the guy from ford spares said these are the ones that are for my car but the knobs thread is too big and the boots hole doesnt fit onto the gearstick top. can anyone tell me if parts EH7213A and EF7277A1A are the right parts?
_________________ OBS35N is gooonnnneeee.
|
|||
| Top | |
|||
| mr_sperm1 |
|
|||
|
no idea. got the parts at home though!
_________________ Maloo - Holden's word for ugly. |
|||
| Top | |
|||
| Big Pete |
|
||
|
This EF/EL/AU momo 5 speed shifter that I have is AU2 7K327 A if that helps at all.
And I've still got one available if anybody is interested. |
||
| Top | |
||
| TROYMAN |
|
||
|
OBS35N wrote: i have just tried to install my gear knob and shifterboot for my ef which i have converted to a manual. now this is the problem..... they dont f**k fit. the guy from ford spares said these are the ones that are for my car but the knobs thread is too big and the boots hole doesnt fit onto the gearstick top. can anyone tell me if parts EH7213A and EF7277A1A are the right parts?
either they have given you the wrong parts or this might be a long shot but you may have a commodore shift as they also have a t5 gearbox and the shifts are slightly different! but still fit.. |
||
| Top | |
||
| Johnson stroker |
|
|||
|
would not be a commodore box as the input shaft is a different length, I replaced my shifter boot and knob recently, I got the EF black knob and EL GT boot, from memory, the boot was a squeeze to get on, the knob, well it pretty much cust the thread into it as it goes, so from new there is not actually a thread in the knob itself.
the EF and EL boots are interchangable. the shape of the lower part of the boot, if its fits in the hole where your auto shifter came from then it is definatly the right one, if not then wrong one. with the knob, you just need to convince it that it is going on. hope that helps somewhat.. Dave
_________________
|
|||
| Top | |
|||
| TROYMAN |
|
||
|
hi
i only ment that the shift might be from a vommodore as they fit straight on but are slightly different.. like i said i think it was a long shot!!! |
||
| Top | |
||
| OBS35N |
|
|||
|
dc_todd wrote: would not be a commodore box as the input shaft is a different length, I replaced my shifter boot and knob recently, I got the EF black knob and EL GT boot, from memory, the boot was a squeeze to get on, the knob, well it pretty much cust the thread into it as it goes, so from new there is not actually a thread in the knob itself.
the EF and EL boots are interchangable. the shape of the lower part of the boot, if its fits in the hole where your auto shifter came from then it is definatly the right one, if not then wrong one. with the knob, you just need to convince it that it is going on. hope that helps somewhat.. Dave it doesnt have a thread but its just too big to fit on it it sucks
_________________ OBS35N is gooonnnneeee.
|
|||
| Top | |
|||
| madeaspack |
|
||
|
if you have a short shift stick it just might not be catching the threads??i just got a short shift stick from EF XR6 and had this problem with el gt boot and momo knob,but its easily fixed
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| OBS35N |
|
|||
|
madeaspack wrote: if you have a short shift stick it just might not be catching the threads??i just got a short shift stick from EF XR6 and had this problem with el gt boot and momo knob,but its easily fixed
how was it easily fixed? mayb use some tape to fill the free play?
_________________ OBS35N is gooonnnneeee.
|
|||
| Top | |
|||
| madeaspack |
|
||
|
if its the short shifter,the plastic end piece of the boot doesnt let the knob go on far enough,so you turn the boot inside out and cut 10mm off the plastic piece which allows the knob to go on further and far enough to start on the thread,does the knob screw on to the stick without the boot,or not at all?
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| old_mate |
|
|||
|
IIRC EA boxes had a thinner thread on the shifter...but i could be wrong
_________________ too many rabbits in china |
|||
| Top | |
|||
| OBS35N |
|
|||
|
madeaspack wrote: if its the short shifter,the plastic end piece of the boot doesnt let the knob go on far enough,so you turn the boot inside out and cut 10mm off the plastic piece which allows the knob to go on further and far enough to start on the thread,does the knob screw on to the stick without the boot,or not at all?
no it doesnt at all which makes me think it might b good to wrap some tape on the thread to fill it out a little
_________________ OBS35N is gooonnnneeee.
|
|||
| Top | |
|||
| ReGiE |
|
|||
|
old_mate wrote: IIRC EA boxes had a thinner thread on the shifter...but i could be wrong
they sure did well my EA box has a thiner thread
_________________ Gooooone - Eb2 Coon - 143RWKW |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 28 guests |
