|
| fordman351 |
|
|||
|
Hey all! I have found the diagnostic display (EL mont) to be very helpful at some stages, but im wondering if there is any way to actually keep the display on all the time? What i mean is, i can bring up the display but say 10 minutes later all gauges die (needles drop to zero, warning lights come on) then comes back to normal including the odometer. Any way to keep the diagnostic display up all the time? It gets a bit annoying pushing the reset button, turning the key and counting to ten fifteen dozen times!
|
|||
| Top | |
|||
| Happy |
|
|||
|
AFAIK no there isn't.
_________________ Owning 1 of 67612 EF GLi Sedans made
|
|||
| Top | |
|||
| Disco Frank |
|
|||
|
nar man from what i have read on here it seems the diag display goes away after time
some ppl have had it on for a few hrs some only 10 mins... damn shame! i am still trying to get the AU diag to work!
_________________ RIP SCOTT |
|||
| Top | |
|||
| Happy |
|
|||
|
is there anything in those diags that isn't on a trip computer?
_________________ Owning 1 of 67612 EF GLi Sedans made
|
|||
| Top | |
|||
| twirqurky |
|
||
|
I have found that if that the longer you leave it flash FORD the longer it will stay. I had the same thing (the needles dropping etc) when I was running the digital sppedo and tacho. That was about 10mins. When I ran the battery voltage and engine temp it stayed on for a while.
|
||
| Top | |
||
| fordman351 |
|
|||
|
{USERNAME} wrote: I have found that if that the longer you leave it flash FORD the longer it will stay. I had the same thing (the needles dropping etc) when I was running the digital sppedo and tacho. That was about 10mins. When I ran the battery voltage and engine temp it stayed on for a while.
My display wont even show the FORD elements, just a blank. |
|||
| Top | |
|||
| chunkz |
|
|||
|
when my speedo was out
i used the digital speedo the only way it would go away is if i turned off the car and turned back on it stayed on... well never went off (unless car was off)
_________________
|
|||
| Top | |
|||
| fairmont1998 |
|
|||
|
{USERNAME} wrote: My display wont even show the FORD elements, just a blank.
When you first enter diagnostic mode, if you leave it for a while it will start flashing ford.
_________________ 2008 WQ Fiesta XR4 |
|||
| Top | |
|||
| 4.9 EF Futura |
|
|||
|
You've been watchin the RPM/Speed readout i'm guessing?
I've found this to be the most demanding output display and causes the dash to hang up as described... i use instant fuel consumtpion, coolant temp and fuel level readout and have had these stay up for months at a time.
_________________ I promise..... I will never die. |
|||
| Top | |
|||
| bentfairmont |
|
|||
|
So whats the process to get it happening, i tried with what i found on another site but it didnt work, or is that bcos i got a series 1 ef fairmont ghia????
_________________ Sometimes when you do something right, people wont be sure you've done anything at all. (Futurama, Episode - Godfellows) |
|||
| Top | |
|||
| twirqurky |
|
||
|
{USERNAME} wrote: So whats the process to get it happening, i tried with what i found on another site but it didnt work, or is that bcos i got a series 1 ef fairmont ghia????
http://www.fordmods.com/forums/documents.php?doc=12 It take s alittle while to get working. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 29 guests |
