So did you order T3, T4 or T5's from that seller on ebay?

It looks great by the way. There was another fella on Ford Forums that did this using a narva blue sleeve but I would rather go this way.

Do you have any tips re: getting to the globe?

as in blacklight? imagine taking someone home whos p****d, and they got in and they realised cricket whites were glowing what would happen then i wonder lol

Yeah blacklights, and yep stuff glows.

Some stuff you wouldn't expect either.

At least it's easy to check if your cash is legit or not.

Got any pics of the blacklights? That would look trippy as!

Hi flacco54,
I have just done the changeover to all LED in my EL ghia,but haven't got to do the dash,ignition or gear selector yet.It's easy except for the glovebox and front and rear reading lights.They are B9S bulbs and Ford has chosen to reverse the polarity so you need to do some soldering,etc with these.Well worth doing though-it looks so much better.

The globe is 10mm diameter and 12mm high, hence went for the T4 option in the auction.

I'm pretty happy with the results. I didn't want to do the sleeve option, that's more of a last resort if I couldn't get the globe I wanted.

Getting to the globe is fairly easy.

1) Under the steering column, lower the adjustment lever.

2) Move the steering column all the way out (towards you) and down (towards your feet).

3) Under the steering column are 3 Phillips Head screws (2 close to your knees, and another further down near the pedals). Remove all three screws.

4) With the screws gone, the plastic housing around the steering column needs to be removed. It actually 'splits' in the middle. Put one hand on the top half and another on the bottom half and it'll split open.

5) You can now see the clear plastic that holds the globe and key validator. It is held in by one phillips head screw and one cable. Unplug the cable, remove the screw, and the plastic unit will simply drop off.

6) The rest should be fairly self explanatory to get to the globe (well, it will be once you remove the small unit). Just use a small flathead screwdriver to open the unit and get to the globe (it simply twists out). Put in a new globe then reverse the procedure to re-install.

i just saw thos pics of that dl ltd and his dash was tacho were all blue... how would i do this with an xh... cause i have a cd that lights up blue, i also have blue neons...

any help would be great

Cheers Vertgo - very helpful. Just ordered my set..........any ideas for the left over globe? anywhere else you can put these?

Glad to help.

Don't know about the left over globe. I'm hanging onto mine regardless.

Take your time with the installation, especially once you remove the plastic unit inside which houses the globe and the key validator. The globe is screwed into a circuit board (see my previous pictures) so you need to be a little careful in removing it and putting in the new one.

I just found this thread. Awesome!

I shall be copying you immediately.

I'm also going to work on the rear passenger map lights and split it into two globes - when on courtesy, the Blue LED will come on, when switched on manually for MAP reading, the White LED will come on.

The centre courtesy light is already bright blue. And the door courtesy lamps (when they go in) will also be changed to blue.


Lukeyson

Always a pleasure Lukeyson. Be sure to keep us posted of your progress.

Opened up my Lab TILA today and found what you were talking about.

T4 has been ordered.


Lukeyson

Looking good.

I'll take a shot from it installed in the car tomorrow.



Lukeyson

 

 

Attachments:

IMG_3118_WEB.jpg [ 23.54 KiB | Viewed 254 times ]

IMG_3120_WEB.jpg [ 24 KiB | Viewed 227 times ]

That's the unit I was talking about Lukeyson, you got it. Good work.

Done

 

 

Attachments:

File comment: I like it! Ignition Barrell comes up a treat. Note that the bright light at the Passenger Seat is my newly installed BF Fairlane Door Trim with courtesy light...... IMG_3137_WEB.jpg [ 101.87 KiB | Viewed 270 times ]